![background image](http://html1.mh-extra.com/html/accu-turn/1250/1250_service-manual_3735141043.webp)
M 0493 -
12
GB
ERR. 34 Falling edge fault detected for
ENCB.
1. Check positioning of the encoder card.
2. Clean the encoder decal.
ERR. 35 Falling edge fault detected for
ENCA.
1. Check positioning of the encoder card.
2. Clean the encoder decal.
ERR. 36 Rising edge fault detected for ENCB. 1. Check positioning of the encoder card.
2. Clean the encoder decal.
ERR. 37 Detected irregular behaviour of the
ENCA falling edge with respect to
the reset rising edge.
1. Check positioning of the encoder card.
2. Clean the encoder decal.
3. Move the encoder card up or down.
ERR. 38 Detected irregular behaviour of the
ENCB falling edge with respect to
the reset rising edge.
1. Check positioning of the encoder card.
2. Clean the encoder decal.
3. Move the encoder card up or down.
STOP
[STOP] button pressed during test.
1. Repeat the test.
3. Encoder count test
Press:
[MENU]
[
]
[ENTER]
The word [dIAgn.] appears
[ENTER]
Confirm
After a brief LED and display test, the wheel position appears on the right-hand display, which must vary in the range
0%127 in a full turn.
On the LED matrix
↑
must appear in clockwise direction and
↓
in anticlockwise direction.
GAUGE CALIBRATION (use an average size wheel with steel rim i,.e. 14” x 6” ± 1”)
- see
AUTOMATIC GAUGES
-
.
POTENZIOMETER DIST.= between 50 and 1000 by pulling out distance gauge completely
.
POTENZIOMETER DIA= between 50 and 1000 by opening diameter gauge wide
.
Sonar 1= (w/monitor) Width (option). From 65000 to 3000 by approaching a target. Range: 40 ÷ 11 cm
Calibrate gauges and check accuracy. it is necessary to set the correct distance rate to obtain an accurate width
measure.
Tolerances:
DIST.= 5 mm
DIAM.= ± ½”
WIDTH= ± ¼”
.
SONAR WIDTH (balancers with monitor):
1.
Mount an average size iron rim, detect accurately width measure by using a traditional gauge or by selecting
the nominal measure written on the rim and adding ¼”
2.
Make the operations described in WIDTH GAUGE (OPTIONAL).
Make sure calibration is correct. Amend distance rate (+/- 1") if necessary until getting an accurate
width indication.
CALIBRATION (see
SELF
-
CALIBRATION
)
.
Use the same wheel as for gauge calibration
.
Set accurate measures, in manual mode if necessary
.
Make self-calibration
CHECKING MACHINE OSCILLATION
After running autocalibration, press [STOP] to return to the standard measuring frame.
Without locking the wheel, measure the machine oscillation as follows:
[MENU]
[
]
[ENTER]
[MENU]+[STOP]+[MENU]
Press in sequence in maximum 5 sec.
The words [Lan] [ci] appear
[ENTER]
Confirm.
The letters [t.L.] [ 10] appear
[START]
A cycle of 10 spins is run with automatic calculation and display
of the maximum oscillation (max. per/- 2 g).
[ENTER]
The following appears [Ini] [~120]: indicates the average unbalance measure
ment start speed in rpm.
[ENTER]
The following appears [End] [~100]: indicates the average unbalance measure
ment end speed in rpm.
Summary of Contents for 1250
