background image

 

EXM-150 MICROSCOPE SERIES  

 

 

 
 

ACCU-SCOPE

®

     

                   

73 Mall Drive, 

Commack, NY  11725  •  631-864-1000  •  www.accu-scope.com 

4

 

INTRODUCTION 

Congratulations on the purchase of your new ACCU-SCOPE

 ®

 microscope. ACCU-SCOPE

 ®

 

microscopes are engineered and manufactured to the highest quality standards. Your microscope will 
last a lifetime if used and maintained properly. ACCU-SCOPE

 ®

 microscopes are carefully assembled, 

inspected and tested by our staff of trained technicians in our New York facility. Careful quality control 
procedures ensure each microscope is of the highest quality prior to shipment.  
 
 

 

UNPACKING AND COMPONENTS 

Your microscope arrived pre-assembled and packed in a molded container. 

Do not discard the 

container

:  

the molded container should be retained for reshipment of your microscope if needed. Avoid 

placing the microscope in dusty surroundings or in high temperature or humid areas as mold and mildew 
will form. Carefully remove the microscope from the Styrofoam container by its arm and base and place 
the microscope on a flat, vibration-free surface. 

 

 

COMPONENTS DIAGRAM 

 

 

 

Carrying Handle 

Monocular Head 

Eyepiece 

Objective 

Stage 

Disc Diaphragm  

Illuminator 

Housing 

Light Adjustment 

Dial 

Fine Focusing 

Knob 

Coarse Focusing 

 Knob 

 

Nosepiece 

Stage Clip 

Cord Hanger 

Model Shown:  

EXM-150

 

(Models Vary) 

Summary of Contents for EXM-150 SERIES















Reviews: