8
GB
WIRE BINDER G1
Step 14:
Unscrew the spool
retainer.
Turn
the
knob
counterclockwise to loosen and
remove the cap. Set the cap
aside.
Step 15:
Remove the spool from
the machine. Pull the spool
straight away from the machine
to slide it off the spindle. Properly
store the spool for future use.
Refer to Section 4 C for
guidelines on spool storage.
Note that the flexible magnet
must remain in place at all times
to prevent slipping of wire.
Step 16:
To remove the rewind
spool from the feed spindle, push
the hub in and turn it clockwise.
Remove the excess paper by
sliding it off the hub.
Note:
If the rewind spool is full of
paper, it may be difficult to
remove. The spool must be
pressed in firmly before rotating
to disengage the pin.
Step 17:
Reinstall the empty paper feed hub to the machine. Slide it
onto the feed hub shaft and rotate counter clockwise until it latches in
place.
Step 18:
Open the top cover and
identify the wire Holder. Check if
there is a cut length of wire on the
Holder (long boxed section). If
there is, remove it by pressing
the Holder release (small boxed
sections) and removing the wire.
Step 19:
If a new spool is to be installed, follow the steps in the
section, Section 7 B.
Step 20:
If no new Supply Spool is to be installed, reinstall the
Element Shield and the Spool Retainer then slide the Element Feeder
Drawer into the machine. Ensure that the drawer is pushed in fully or
the message “Push Feeder In” will appear on the LCD. Close the
Element Feeder Door.
B.
Installing a New Supply Spool Into the Machine:
Step 1:
Stop the printer/copier.
Step 2:
Open the Element Feeder Door.
Step 3:
Slide the feeder drawer out from the machine by pulling on
the handle.
Step 4:
If applicable, follow the instructions in Section A to remove
the previously installed element spool.
Step 5:
Remove the wire
shield. Pull on the wire shield
handle to remove the entire
shield, and place the shield
safely on top of the element
feeder.
Step 6:
Remove the spool retainer from the spindle. Turn the knob
counter clockwise until the cap can be removed, and set it aside.
Step 7:
Remove the Supply
Spool from its carton and remove
the plastic shrink wrap.
Method 1: Remove the plastic by
cutting across using scissors.
Caution:
Do not cut the carrier
paper or wire when cutting the
plastic, doing so may ruin the
spool.
Note:
Do not remove the
cardboard retainer at this point.
The wire will unwind if it is not
secured throughout the process
and may lead to jams.
Method 2: With the plastic still on
the Supply Spool proceed to
Steps 8 & 9 before slowly
unwinding it.
Step 8:
Install the spool by
sliding the spool onto the hub.
The circular barcode label must
face towards the inside of the
machine.
The
product
description label on the hub must
face out.
Summary of Contents for GBC G1
