Abus 17787 Operation Instructions Manual Download Page 13

Page: 13 / 37

Page 13

AN120076.000_EN

6.2

Regulations

The load indicator systemLIS–SE is in accordance with

the following codes and standards:

NSR 20014/35/EG

(low voltage)

EMC 2014/30/EG

(electromagnetic compatibility)

EN 61000- 6- 4

(interference emission)

EN 61000- 6- 2

(resistance to interferences)

Electrical installation work must be performed in accor-

dance with the following general codes and standards:

IEC 60364- 5- 56

Requirements for the installation of power systems with

rated voltages up to 1000V

EN 60204- 32

Safety of machinery: Electrical equipment of machines;

requirements for hoists.

For special applications, other standards and regula-

tions may also be applicable.

Safety warnings:

You must not carry out any work inside the

unit.

In the event of a defect in anLIS–SE unit, please contact

our service department.

In order to avoid the risk of serious injury and severe da-

mage, only persons qualified to work on electric power

systems may work on the units. Before installing any

commissioning the units, these persons must carefully

read the operating instructions and observe the safety

instructions.

Attention!

Any modifications to ABUS products and any

parts installed in or on ABUS products which

could impair the safety of the products must

be approved by the manufacturer. ABUS will

not be liable for any injury, loss or damage

which may occur as a result of modifications

which have not been approved or the use of

products other than for the intended pur-

pose.

Note:

ELECTROMAGNETIC COMPATIBILITY

The unit has been designed in accordance

with the EMC directive no. 2014/30/EG.

_________________________________

Malfunctions

7.1

Causes and Remedies

TheLIS–SE displays the following error codes on the operator terminal or the load display.

Err–Code Explanation

Remedy

Err 1

Current correction factor not entered

Enter current correction factor in parameter P 1.3

Err 2

Rated load capacity not set

Enter load capacity in parameter P 0.1

Err 3

Unit not set

Set unit with known load

Err 6

Is displayed when parameter P 2.3 is selected

Setting load too low or setting/connection

error

Increase load to 80 % of rated load capacity

Err 7

Setting not correctly completed

see page 14

Err 8

Data save error

Replace unit

Err 9

Data read error

Press ”Enter” until the function returns. Otherwi-

se, replace unit

U_I

Measured rotor power input <10 Watt

Check the basic setting of the unit; if the setting

is OK, the problem has probably been caused by

the wiring factor.

The input and output voltage data required for trouble-

shooting are stated in Section 4 ”Technical Data”.

If any other malfunctions occur, please contact our ser-

vice centre (see Section 7.2).

7.2

Service

Notes:

The ABUS Service Centre can be reached

day and night.

Summary of Contents for 17787






































Search results

Summary of Contents for 17787

Reviews:

Related manuals for 17787

Brands by name

Popular brands

Abus 17787, Operation Instructions Manual

Search results

Summary of Contents for 17787

Reviews:

Related manuals for 17787

Brands by name

Popular brands