manualshive.com logo in svg

ABSCO SHEDS CPDW50, Assembly & Instruction Manual

Share
Download
ABSCO SHEDS CPDW50 Assembly & Instruction Manual Download Page 15

STEP 10

IMMEDIATE MAINTENANCE:

RB

BEND THE ENDS OF 16 FLAT STRIPS
(270mm X 25mm) AS SHOWN AND
SECURE AT MAXIMUM 1500mm

         CENTRES WITH ONE SCREW
                  AT EACH END.

CLEAN DOWN ALL ROOF AND EDGE/CROSS BEAM INTERNAL AREAS. METAL FILINGS FROM
DRILLING HOLES AND USING SELF DRILLING SCREWS CAN CAUSE DISCOLORATION AND
CORROSION TO ROOF SHEETS AND GALVANIZED FRAMING SECTIONS.

DP-5

DP-3

DP-2

DP-1

DP-4

DS

CUT A ROUND HOLE 51mm IN DIAMETER IN ONE END OF THE REAR EDGE BEAM. THIS CAN BE
DONE BY DRILLING A SERIES OF 3mm HOLES AND THEN PUNCHING OUT THAT SECTION. FIT THE
GALVANISED GUTTER DROP AND SEAL WITH SILICONE. FASTEN THE DOWNPIPES AND BENDS

AS SHOWN. BEND THE 270 x 25 FLAT STRIPS (DS) TO SHAPE AND FASTEN THE DOWNPIPE TO
THE COLUMNS.

ABSCO INDUSTRIES

ASSEMBLY INSTRUCTION MANUAL

CARPORT MODEL: CPDW50  

10-05-2017  

      

Absco Industries

Skillion Carport Model: CPDW50

PAGE 15

Summary of Contents for CPDW50




















Reviews:

No comments

Brands by name

Popular brands

Load more brands