Call Toll Free:
877-788-7253
Email:
11
Fig 16.
Fig 18.
Fig 14.
Fig 17.
Fig 13.
Fig 19.
Fig 15.
Stirrer
Bolt and
flat washer
Flat washer
and locknut
Align slots on stirrer guard
over holes in hopper wall.
Long hopper support brackets
welded on main support frame.
Remove lower knob and washer
and set aside for the moment.
Outgoing
shaft.
14.
Slide (1) Ø28 shim onto both left and right axle shaft (
Fig
27
). Slide (1) wheel onto both left and right axle shafts. The
side of the wheel with the long tube portion of the hub (with
the small hole going thru the side of the hub) faces inward
toward the gearbox on the axle (
Fig 28 & 29
). Slide (1) Ø20
washer onto both left and right axle shaft (
Fig 29
). On both
left and right axle shafts, insert bent cotter pin into hole at
the end of the axle shaft to secure the washer, wheel and
shim (
Fig 30
).
15.
Locate the M6x45 hex head bolt, (2) Ø6 flat washers and
the M6 locknut.
On the left axle shaft is a 2nd hole going thru the shaft that
will line up with the hole going thru the side of the wheel
hub (shown in
Fig 28
). Slide (1) washer onto the M6x45 bolt
then slide the bolt thru the hub and axle holes. Slide the
other washer onto the bolt then thread the M6 lock nut onto
the bolt and tighten using (2) 10mm wrenches or socket set
(
Fig 31
).
16.
Locate towing hitch with pivoting brackets, (6) M8x40 hex
head bolts, (6) Ø8 washers and (6) M8 nuts (
Fig 32
).
17.
Mount 1st pivot bracket to main support frame by
inserting (2) M8x40 bolts thru pivot bracket holes then thru
main support frame holes. Slide (1) Ø8 washer onto both
bolts then thread (1) M8 nut onto each bolt - hand tighten
only. Pivot bracket should be parallel to spreader disc when
properly mounted. (
Fig 33 & 34
). Slide towing hitch onto
pivot bracket with 2nd pivot bracket attached to towing
hitch (
Fig 35
). Mount 2nd pivot bracket to main support
frame by inserting (2) M8x40 bolts thru pivot bracket holes
then thru main support frame holes. Slide (1) Ø8 washer
onto both bolts then thread (1) M8 nut onto each bolt - hand
tighten only. Pivot bracket should be parallel to spreader
disc when properly mounted (
Fig 36
). Rotate both angled
brackets (with multiple holes in each bracket) attached to
towing hitch until the hole at the end of each bracket line up
with the holes on the main support frame. Insert (1) M8x40
bolt thru angle bracket hole and hole in main support frame.
Slide (1) Ø8 washer onto bolt then thread (1) M8 nut onto
each bolt - hand tighten only. Repeat this with 2nd angled
bracket on other side. (
Fig 37
). Once all (6) bolts and nuts are
installed, fully tighten using (2) 13mm wrenches or socket
set.
18.
The broadcast spreader is now fully assembled (
Fig 38 &
39
).
19.
Once the spreader is hitched to the tow vehicle, position
the spreader disc to be parallel to the ground by removing
the bolts on the two angled brackets using (2) 13mm
wrenches or socket set and line up one of the holes in the
angled brackets with the holes in the towing hitch that
makes the spreader disc parallel to the ground. Replace the
bolts, washers and nuts and retighten (
Fig 40
).
