ABB UniGear ZVC Installation, Operation And Maintenance Instructions Manual Download Page 51 | Manualshive

Page: 51 / 56

ABB UniGear ZVC Installation, Operation And Maintenance Instructions Manual Download Page 51

9.5 Spares, auxiliary material and lubricants
9.5.1 Spare parts

A spare parts list is available on request for
procurement of spare parts. It basically includes
moving parts and parts subject to wear. When
parts are required, the serial number of the
relative switchgear or switching device should
always be quoted.

506752901: -DU feeder 24-60 V DC
506752902: -DU feeder 100-250 V AC/DC
2RDA021449A9001: -DU feeder 88-124 V DC
18419: -S6, -S302, -S303 aux. switch
6109200: -S301 fuse blown aux. switch
6250685: -S3 ELFIN switches assembly
6250800: -Y2 trip coil 24-30 V DC
6250801: -Y2 trip coil 48-60 V DC
6250802: -Y2 trip coil 110-130 V DC
6250803: -Y2 trip coil 220-250 V DC
6250804: -Y2 trip coil 110-130 V AC
6250805: -Y2 trip coil 220-250 V AC
6200103: current interlock assembly
6250306: 3.6 kV fuse adapter
6230310: door interlock

9.5.2 Auxiliary materials, lubricants

Lubricant: Isoflex Topas NB 52

Halogen-free cleansers: ETHANOL F 25 M (for
general cleaning)

Touch-up paint: Standard colour RAL 7035

9.6 Tools

6E0635: trip release operator

6030792: door key

GCE8004261R0101: door key with handle

6030667: racking handle

6030699/C: earth switch handle

6500831: DT lower truck operating handle

6050192: racking handle for motorised truck

6E0635

6030792

6030699/C

GCE8004261R0101

M A I N T E N A N C E

51

—
9/4 Fuses module
—
9/5 ZVC racking
blocking coil
replacement 1 of 2

—
9/7

«
...
49
50
51
52
53
...
»

Summary of Contents for UniGear ZVC

























































Reviews:

No comments