manualshive.com logo in svg

ABB UniGear ZVC, Installation, Operation And Maintenance Instructions Manual, Page: 18 / 56

Share
Download
ABB UniGear ZVC Installation, Operation And Maintenance Instructions Manual Download Page 18

4.6.1 Versions available

•  

Electrically held

•  

Mechanically latched

4.6.2 Standard equipment

•  

Operating mechanism

•  

Fuse blown indicator with 1 N/O auxiliary 
contacts 

•  

Mechanical operation counter

•  

3 N/O+3 N/C contactor auxiliary contacts

•  

24 pin automatic connection plug

•  

Contactor ISOLATED and SERVICE indicator

•  

Contactor ON-OFF (I-O) indicator

•  

Emergency trip provision (only for mechanically 
latched)

4.6.3 Optional equipment

•  

Control voltage transformer

•  

Mechanical latch coil

•  

Trip circuit supervision provision

•  

Racking blocking coil

•  

Fuse blown indicator with 1 N/O or 1 N/C 
auxiliary contacts

4.7 Panel variants
4.7.1 Motor starter (direct on line)

Motor starter (DOL) ZVC

Ratings

Circuit full load 
current
Rated frequency
Rated voltage
Width
Depth 

1

Height 

2

A

Hz
kV
mm
mm
mm

400

50/60
7.2
325
1304
2200

1  Bottom power cable entry version. Top cable power entry version 

1554 mm with gas duct.

2  Larger LV compartment with corresponding total panel height 

2400 and 2596 mm available.

Refer to shipping sections in the general 
arrangement drawing.

Note the location of the power cable entry in the 
contract drawings.

Pay special attention to clauses 6.4 to join 
panels and 6.5 to install busbars.

4.7.2 Slip ring induction starter 

ROTOR

STATOR

Note: 
external secondary resistor

Slip ring induction

ZVC-SRI Ratings

Circuit full load 
current
Rated frequency
Rated voltage
Width
Depth 

1

Height 

2

A

Hz
kV
mm
mm
mm

400

50/60
7.2
325
1304
2200

1  Bottom power cable entry version. Top cable power entry version 

1554 mm with gas duct.

2  Larger LV compartment with corresponding total panel height 

2400 and 2596 mm available.

Slip ring induction starter type ZVC-SRI

Slip ring or wound rotor motor is an induction 
machine where the rotor comprises a set of 
coils that are terminated in slip rings to which 
external resistors can be connected. The stator 
is the same as is used with a standard squirrel 
cage motor.

Refer to shipping sections in the general 
arrangement drawing. Note the location of the 
power cable entry in the contract drawings.

Pay special attention to clauses 6.4 to join 
panels and 6.5 to install busbars.

18

U N I G E A R   Z V C  

M E D I U M   V O L T A G E   P R O D U C T S

Summary of Contents for UniGear ZVC

























































Reviews:

No comments