ABB TPL65VA32 Operation Manual Download

Page: 96 / 124

Operation Manual / TPL65VA32/33

Disassembly and assembly

Removing cartridge group

8.5

Page 94

ber

2016

L2464_

ion



Unplug cable connector (86515) and unscrew speed sensor (86505)

with O-ring (86506).



Remove the O-ring (42012).



Remove the three screws (61059) together with their Verbus Ripp®

washers (61058).



Attach one lifting gear each to the two fins of the bearing casing pro-

vided for this purpose.



Evenly press off cartridge group by screwing press-off screws (90900)

into the designated holes.

CAUTION

If the rotor blades have insufficient or no clearance, the blades and cas-

ing could be damaged.



Check that the blades do not rub on the turbine diffuser by rotating

the rotor.

Summary of Contents for TPL65VA32





























































































































Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands

ABB TPL65VA32, Operation Manual

Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands