ABB TPL65VA32 Operation Manual Download

Page: 63 / 124

Operation Manual / TPL65VA32/33

Maintenance

Cleaning the compressor during

operation

5.3

Page 61

ber

2016

L2464_

ion

Wet cleaning using external water-pressure vessel (XC3)

Operating state prerequisites for wet cleaning XC3

NOTICE

To be able to carry out a satisfactory cleaning process which has been

tested and is recommended by ABB Turbo Systems, the following pre-

requisites must be fulfilled:



Engine load 50 ... 85%



Start of cleaning cycle in accordance with following description for

wet cleaning operation with XC3.

Compressor wet cleaning procedure with XC3



It is mandatory to fulfil the operating condition prerequisites before

cleaning compressors with XC3.



Remove the sealing plug (X).



Fill the vessel with the required volume of clean water (see the Table

of cleaning parameters).

5.3.2

Operating the water

pressure vessel

Summary of Contents for TPL65VA32





























































































































Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands

ABB TPL65VA32, Operation Manual

Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands