ABB TPL65VA32 Operation Manual Download

Page: 103 / 124

Operation Manual / TPL65VA32/33

Disassembly and assembly

Installing cartridge group

8.9

Page 101

ber

2016

ZTL

2464_

ion

CAUTION

If there is no or insufficient clearance between the rotor turbine blades

and the turbine diffuser, the blades and the turbine diffuser (casing) can

be damaged.



Check that the blades do not rub on the turbine diffuser by rotating

the rotor.



Remove the lifting gear.



Fit O-ring (42012).



Screw in the speed sensor (86505) together with the O-ring (86506)

and plug in the cable connector (86515).



Fit the O-ring (77005) to the wall insert (77000).



Fit the lifting gear and the swivel lifting eye (90235).



Align and fit the wall insert (77000) using the centring screw (90187).



Place the diffuser (79000) in position using the swivel lifting eye

(90235).



Remove the swivel lifting eye (90235).



Fit the screws (72002).

Summary of Contents for TPL65VA32





























































































































Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands

ABB TPL65VA32, Operation Manual

Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands