ABB TPL65VA32 Operation Manual Download

Page: 104 / 124

Operation Manual / TPL65VA32/33

Disassembly and assembly

Installing cartridge group

8.9

Page 102

ber

2016

L2464_

ion



Attach lifting gear to lifting device (90190) and turn compressor casing

(72000).



By hand, screw three press-off nuts (61090) onto bearing casing

studs, equally spaced around circumference and up to end of thread.



Push compressor casing (72000) onto cartridge group to fit snugly and

fasten it using nuts (61037).



Secure three press-off nuts (61090) against compressor casing

(72000) by tightening them to specified torque. (See chapter Table of

tightening torques.)



Remove lifting device (90190).



Fit sealing air line (56501) between compressor casing (72000) and

variable turbine geometry module (56100).

Summary of Contents for TPL65VA32





























































































































Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands

ABB TPL65VA32, Operation Manual

Search results

Summary of Contents for TPL65VA32

Reviews:

Related manuals for TPL65VA32

Brands by name

Popular brands