background image

Contact us 

 

42/18-4

6

-EN R

e

v. L 

07.2017

 

ABB Limited 
Measurement & Analytics 

Howard Road, St. Neots 
Cambridgeshire, PE19 8EU 
UK 
Tel: 

+44 (0)870 600 6122 

Fax: 

+44 (0)1480 213 339 

Mail: [email protected] 
 

ABB Inc. 
Measurement & Analytics 

125 E. County Line Road 
Warminster, PA 18974 
USA 
Tel: 

+1 215 674 6000 

Fax: 

+1 215 674 7183 

 
ABB Automation Products GmbH 
Measurement & Analytics 

Schillerstr. 72 
32425 Minden 
Germany 
Tel: +49 

571 

830-0 

Fax: +49 

571 

830-1806 

 

www.abb.com/positioners 

 

 

 

 

Note 

We reserve the right to make technical changes or 

modify the contents of this document without prior 

notice. 

With regard to purchase orders, the agreed 

particulars shall prevail. ABB does not accept any 

responsibility whatsoever for potential errors or 

possible lack of information in this document. 

 

We reserve all rights in this document and in the 

subject matter and illustrations contained therein. 

Any reproduction, disclosure to third parties or 

utilization of its contents – in whole or in parts – is 

forbidden without prior written consent of ABB. 

 

Copyright© 2017 ABB 

All rights reserved 

 

3KXE311001R4201 

Original instruction 

 

 

 

 

 

Notizen 

 
 

Summary of Contents for TEIP11





















Reviews: