ABB SPA-ZC 402 Installation And Commissioning Manual Download Page 61

Page: 61 / 112

General requirements

Table 8.2.-1

Environmental test and conditions

Recommended service temperature range
(continuous)

-10...+55

Limited temperature range (short-term)

-40...+85

Transport and storage temperature range

-40...+70

C according to the IEC 60068-2-48

Dry heat test

According to the IEC 60068-2-2

Dry cold test

According to the IEC IEC 60068-2-1

Damp heat test, cyclic

According to the IEC 60068-2-30

Table 8.2.-2

Electromagnetic compatibility tests

EMC immunity test level meets the requirements listed below.

1 MHz burst disturbance test, class III According to the IEC 60255-22-1

Common mode

2.5 kV

Differential mode

1.0 kV

Electrostatic discharge test, class III

According to the IEC 61000-4-2 and IEC 60255-22-
2

For contact discharge

8 kV

For air discharge

Not applicable

Radio frequency interference tests

Conducted, common mode

According to the IEC 61000-4-6 and IEC 60255-22-
6 10 V (rms), f=150 kHz...80 MHz

Radiated, amplitude-modulated

According to the IEC 61000-4-3 and IEC 60255-22-
3 10 V/m (rms), f=80...2700 MHz

Radiated, pulse-modulated

According to the ENV 50204 and IEC 60255-22-3
10 V/m, f=900 MHz

Fast transient disturbance tests

According to the IEC 60255-22-4 and IEC 61000-4-
4

All terminals

4 kV

Surge immunity test

According to the IEC 60255-22-5 and IEC 61000-4-
5

Power supply, SPA-ZC402xxxA

4 kV line-to-earth, 2 kV line-to-line

Power supply, SPA-ZC402xxxC

2 kV line-to-earth, 1 kV line-to-line

RJ45-Cable

2 kV line-to-earth

Power frequency (50 Hz) magnetic field
IEC 61000-4-8

300 A/m continuous

Electromagnetic emission tests

According to the EN 55011

Conducted, RF-emission (Mains
terminal)

EN 55011, class A, IEC 60255-25

Radiated RF-emission

EN 55011, class A, IEC 60255-25

CE approval

Complies with the EMC directive 2004/108/EC and
the LV directive 2006/95/EC

SPA/ Ethernet Adapter

SPA to IEC 61850 Gateway

Installation and Commissioning Manual

SPA-ZC 402

1MRS755380

Summary of Contents for SPA-ZC 402

















































































































Search results

Summary of Contents for SPA-ZC 402

Reviews:

Related manuals for SPA-ZC 402

Brands by name

Popular brands

ABB SPA-ZC 402, Installation And Commissioning Manual

Search results

Summary of Contents for SPA-ZC 402

Reviews:

Related manuals for SPA-ZC 402

Brands by name

Popular brands