ABB Relion SAM600 Applications Manual Download Page 9

Page: 9 / 92

4.12

Elapsed time integrator with limit transgression and overflow supervision TEIGAPC.....38

4.12.1

Identification................................................................................................................................38

4.12.2

Application....................................................................................................................................39

4.12.3

Setting guidelines....................................................................................................................... 39

4.13

Comparator for integer inputs - INTCOMP.................................................................................39

4.13.1

Identification................................................................................................................................39

4.13.2

Application....................................................................................................................................39

4.13.3

Setting guidelines....................................................................................................................... 39

4.13.4

Setting example...........................................................................................................................40

4.14

Comparator for real inputs - REALCOMP....................................................................................40

4.14.1

Identification................................................................................................................................40

4.14.2

Application.................................................................................................................................... 41

4.14.3

Setting guidelines........................................................................................................................41

4.14.4

Setting example........................................................................................................................... 41

Section 5

Monitoring.........................................................................................................43

5.1

Gas medium supervision SSIMG................................................................................................... 43

5.1.1

Identification................................................................................................................................43

5.1.2

Application....................................................................................................................................43

5.1.3

Setting guidelines....................................................................................................................... 43

5.2

Liquid medium supervision SSIML...............................................................................................44

5.2.1

Identification................................................................................................................................44

5.2.2

Application....................................................................................................................................44

5.2.3

Setting guidelines....................................................................................................................... 44

5.3

Breaker monitoring SSCBR............................................................................................................ 45

5.3.1

Identification................................................................................................................................45

5.3.2

Application....................................................................................................................................45

5.3.3

Setting guidelines....................................................................................................................... 45

5.3.3.1

Setting procedure on the IED................................................................................................ 46

5.4

Disturbance report DRPRDRE........................................................................................................47

5.4.1

Identification................................................................................................................................ 47

5.4.2

Application....................................................................................................................................47

5.4.3

Setting guidelines....................................................................................................................... 48

5.4.3.1

Recording times....................................................................................................................... 50

5.4.3.2

Binary input signals..................................................................................................................51

5.4.3.3

Analog input signals.................................................................................................................51

5.4.3.4

Sub-function parameters....................................................................................................... 52

5.4.3.5

Consideration............................................................................................................................52

5.5

Limit counter L4UFCNT.................................................................................................................. 53

5.5.1

Identification................................................................................................................................ 53

5.5.2

Application....................................................................................................................................53

5.5.3

Setting guidelines........................................................................................................................53

Section 6

Ethernet-based communication.....................................................................55

6.1

Access point......................................................................................................................................55

6.1.1

Application....................................................................................................................................55

6.1.2

Setting guidelines....................................................................................................................... 55

Table of contents

Switchgear control unit SAM600-IO

Application manual

Summary of Contents for Relion SAM600




























































































Search results

Summary of Contents for Relion SAM600

Reviews:

Brands by name

Popular brands

ABB Relion SAM600, Applications Manual

Search results

Summary of Contents for Relion SAM600

Reviews:

Brands by name

Popular brands