ABB Relion SAM600 Applications Manual Download Page 8

Page: 8 / 92

Logic................................................................................................................... 27

4.1

Tripping logic SMPPTRC ................................................................................................................ 27

4.1.1

Identification................................................................................................................................ 27

4.1.2

Application.................................................................................................................................... 27

4.1.2.1

Three-phase tripping...............................................................................................................28

4.1.2.2

Single- and/or three-phase tripping....................................................................................28

4.1.2.3

Single-, two- or three-phase tripping.................................................................................. 30

4.1.2.4

Lock-out..................................................................................................................................... 30

4.1.2.5

Blocking of the function block...............................................................................................30

4.1.3

Setting guidelines....................................................................................................................... 30

4.2

Trip matrix logic TMAGAPC............................................................................................................ 31

4.2.1

Identification................................................................................................................................ 31

4.2.2

Application.................................................................................................................................... 31

4.2.3

Setting guidelines........................................................................................................................31

4.3

Logic for group alarm ALMCALH...................................................................................................31

4.3.1

Identification................................................................................................................................ 31

4.3.2

Application.................................................................................................................................... 31

4.3.3

Setting guidelines........................................................................................................................32

4.4

Logic for group alarm WRNCALH..................................................................................................32

4.4.1

Identification................................................................................................................................ 32

4.4.1.1

Application.................................................................................................................................32

4.4.1.2

Setting guidelines.................................................................................................................... 32

4.5

Logic for group indication INDCALH............................................................................................32

4.5.1

Identification................................................................................................................................ 32

4.5.1.1

Application.................................................................................................................................32

4.5.1.2

Setting guidelines.................................................................................................................... 32

4.6

Configurable logic blocks...............................................................................................................33

4.6.1

Application.................................................................................................................................... 33

4.6.2

Setting guidelines........................................................................................................................33

4.6.2.1

Configuration............................................................................................................................33

4.7

Fixed signal function block FXDSIGN...........................................................................................34

4.7.1

Identification................................................................................................................................34

4.7.2

Application....................................................................................................................................34

4.8

Boolean 16 to Integer conversion B16I........................................................................................ 34

4.8.1

Identification................................................................................................................................34

4.8.2

Application....................................................................................................................................34

4.9

Boolean to integer conversion with logical node representation, 16 bit BTIGAPC............ 35

4.9.1

Identification................................................................................................................................ 35

4.9.2

Application....................................................................................................................................35

4.10

Integer to Boolean 16 conversion IB16.........................................................................................36

4.10.1

Identification................................................................................................................................36

4.10.2

Application....................................................................................................................................36

4.11

Integer to Boolean 16 conversion with logic node representation ITBGAPC.......................37

4.11.1

Identification................................................................................................................................ 37

4.11.2

Application....................................................................................................................................38

Table of contents

Switchgear control unit SAM600-IO

Application manual

Summary of Contents for Relion SAM600




























































































Search results

Summary of Contents for Relion SAM600

Reviews:

Brands by name

Popular brands

ABB Relion SAM600, Applications Manual

Search results

Summary of Contents for Relion SAM600

Reviews:

Brands by name

Popular brands