ABB Relion SAM600 Applications Manual Download Page 10

Page: 10 / 92

6.2

Redundant communication........................................................................................................... 56

6.2.1

Identification................................................................................................................................56

6.2.2

Application....................................................................................................................................56

6.2.3

Setting guidelines........................................................................................................................57

6.3

Routes................................................................................................................................................ 58

6.3.1

Application....................................................................................................................................58

6.3.2

Setting guidelines....................................................................................................................... 58

Section 7

Station communication................................................................................... 59

7.1

IEC 61850-8-1 communication protocol......................................................................................59

7.1.1

Application IEC 61850-8-1..........................................................................................................59

7.1.2

Setting guidelines....................................................................................................................... 60

7.1.3

Horizontal communication via GOOSE...................................................................................60

7.1.3.1

Sending data.............................................................................................................................60

7.1.3.2

Receiving data...........................................................................................................................61

Section 8

Security.............................................................................................................. 63

8.1

Authority status ATHSTAT............................................................................................................. 63

8.1.1

Application....................................................................................................................................63

8.2

Self supervision with internal event list INTERRSIG..................................................................63

8.2.1

Application....................................................................................................................................63

8.3

Change lock CHNGLCK................................................................................................................... 64

8.3.1

Application....................................................................................................................................64

8.4

Denial of service SCHLCCH/RCHLCCH .......................................................................................65

8.4.1

Application....................................................................................................................................65

8.4.2

Setting guidelines....................................................................................................................... 65

Section 9

Basic IED functions...........................................................................................67

9.1

IED identifiers TERMINALID........................................................................................................... 67

9.1.1

Application....................................................................................................................................67

9.2

Product information PRODINF...................................................................................................... 67

9.2.1

Application....................................................................................................................................67

9.2.2

Factory defined settings........................................................................................................... 68

9.3

Measured value expander block RANGE_XP...............................................................................69

9.3.1

Identification................................................................................................................................69

9.3.2

Application....................................................................................................................................69

9.3.3

Setting guidelines....................................................................................................................... 69

9.4

Parameter setting groups..............................................................................................................69

9.4.1

Application....................................................................................................................................69

9.4.2

Setting guidelines....................................................................................................................... 70

9.5

Signal matrix for binary inputs SMBI........................................................................................... 70

9.5.1

Application....................................................................................................................................70

9.5.2

Setting guidelines....................................................................................................................... 70

9.6

Signal matrix for binary outputs SMBO ......................................................................................70

9.6.1

Application....................................................................................................................................70

9.6.2

Setting guidelines........................................................................................................................ 71

9.7

Signal matrix for mA inputs SMMI................................................................................................ 71

Table of contents

Switchgear control unit SAM600-IO

Application manual

Summary of Contents for Relion SAM600




























































































Search results

Summary of Contents for Relion SAM600

Reviews:

Brands by name

Popular brands

ABB Relion SAM600, Applications Manual

Search results

Summary of Contents for Relion SAM600

Reviews:

Brands by name

Popular brands