manualshive.com logo in svg

ABB PVS-60-TL-R-US, Product Manual

Share
Download
ABB PVS-60-TL-R-US Product Manual Download Page 107

- 107 -

000876AG

7 - Operation

L

ED behaviour

The LEDs on the front panel may behave in different ways depending on 

the inverter’s operational status. 

All possible LED activation combinations are shown in the following ta-

ble. In particular, each LED could behave in one of the following ways:

 = LED on

 = LED flashing slow (2 seconds on / 2 seconds off)

 = LED flashing fast (0.2 seconds on / 0.2 seconds off)

 = LED off

 = Any one of the conditions described above

LED status

Operating state

green:

     

yellow:     

red:     

Firmware programming

The inverter firmware is being programmed

green:

     

yellow:     

red:     

Night mode (inverter automatically switches off) 

The inverter is in night time switch-off mode (input voltage less than 70% of the set start-up 

voltage).

green:

     

yellow:     

red:     

Inverter initialization 

This is a transitional state due to verification of the operating conditions. During this stage the 

inverter checks that the conditions for connecting to the grid are met.

green:

     

yellow:     

red:     

The inverter is connected and is feeding power into the grid

Normal operation. During this stage, the inverter automatically tracks and analyses the pho-

tovoltaic generator's maximum power point (MPP).

green:

     

yellow:     

red:     

Disconnection from the grid

Indicates lack of grid voltage. This condition does not allow the inverter to connect to the grid 

(the inverter display shows the message "Missing Grid").

green:

     

yellow:     

red:     

Warning indication: (W message codes) or Error: (E message codes)

- Indicates that the inverter control system has detected a warning (W) or error (E). It is possible 

to identify the type of problem generated with the Aurora Manager LITE software (see the alarm 

messages).

green:

     

yellow:     

red:     

Temperature protection trip

Indicates that the trip relating to internal temperatures (insufficient or excessive temperature) 

may have been activated

green:

     

yellow:     

red:     

Anomaly in the insulation system of the photovoltaic generator

Indicates that a leakage to earth from the PV generator has been detected, causing the in-

verter to disconnect from the grid. 

Summary of Contents for PVS-60-TL-R-US















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands