ABB PSE18 Installation And Commissioning Manual Download

Page: 70 / 104

Softstarters Type PSE18...PSE370 Installation and commissioning manual 1SFC132057M0201

70 Chapter 7

Figure 7.27 Fieldbus Control parameter

displayed

7.5.12

FieldBus Control (optional hardware required)

This parameter is used for

configuration of the fieldbus communication. Con

necting the PSE Softstarter to the

FieldBusPlug automatically enables fieldbus

communication. To enable control of the softstarter using fieldbus, this parameter
must be set to On. If FieldBus Control is set to OFF, fieldbus can only be used for

monitoring softstarter data.

If this parameter is set to On, the softstarter might trip on

fieldbus fault if no field

bus communication is available. If the intention is to run without fieldbus control,

this parameter should be set to OFF.

Caution!

The motor may

start unexpectedly if there is a start signal present when do

ing any of the actions listed below.

•

Switching from one type of control to another (fieldbus control /

hard-

wire control). Remember that when parameter Fieldbus Fault Reaction

is set to LocC, this switch can happen automatically.

•

Resetting of

events.

•

If using automatic event reset.

Fieldbus Control parameters and settings

Display

Default
value

Setting
range

Description

1SFC132264F000

Ready

Run

Exit

Select

Reset

Protection

Fault

OFF

OFF/On

Control of the softstarter with

fieldbus.

255

0...255

Fieldbus Address

dPoF

dPoF/dPon

Possible to block parameter down-
load from PLC

LocC

LocC/trIP

Operation When Fault

HAnd

HAnd/Auto

Type of operation for reset of Field-
bus Fault

1. 255 =

Address of FieldBus Control will be used.

2.  Accessible only if Fieldbus Control previously is set to On.
3.  Accessible only if trIP is previously selected.
4.  HAnd  =  Manual reset:

When tripping will stop the motor, a manual reset is

required before restart can be done.

Auto = Automatic reset:

When tripping will stop the motor, an automatic reset is

performed before the unit is ready for restart.

More information about Fieldbus communication and optional accessories is avail-
able in Chapter 8 Fieldbus communication.

Summary of Contents for PSE18









































































































Search results

Summary of Contents for PSE18

Reviews:

Related manuals for PSE18

Brands by name

Popular brands

ABB PSE18, Installation And Commissioning Manual

Search results

Summary of Contents for PSE18

Reviews:

Related manuals for PSE18

Brands by name

Popular brands