ABB PowerValue RT G2 User Manual Download Page 43

Page: 43 / 50

LCD Message

Explanation

Solution

Warning 06:LineVoltError

As stated.

Check if the input wiring is correct or
contact service personnel

Warning 07:LinePhaseFail

As stated.

Contact service personnel

Warning 08:OverCharge

Battery voltage is too high.

Check the setting of Nominal Battery
voltage and contact service personnel.

Warning 09:ChgFail

Battery voltage is detected as low
level. However, the charge is able to
work.

Contact service personnel.

Warning 0A:OverTemp

The temperature in UPS is higher

than 75°C. At this time, the UPS is

still running.

Check if the ambient temperature is over
specification.
Or contact service personnel.

Warning 0B:PFCCurUnbal

PFC current is unbalance.

Contact service personnel

Warning 0C:FanError

Fan error.

Check if the fan is blocked or contact
service personnel.

Warning 0D:LineFuseOpen

Fuse is broken.

Turn off UPS and replace a good one with
the broken one. If UPS fails again after you
do this, contact the service personnel.

Warning 0E:IICEepromFail

EEPROM operation error

Contact service personnel.

Warning 11:BypassIpNLoss

Neutral loss.

Check if the Neutral connection is well and
contact service personnel.

Warning 12:BpsPhaseError

Bypass phase error.

Check if the Bypass phase sequence is
correct and contact service personnel.

Warning 13:BpsVoltError

Bypass voltage error.

Check the wiring or contact service
personnel

Warning 14:BpsPhaseFail

As stated.

Contact service personnel

Warning 15:OverLoad

In line mode, the connected devices
are demanding more power than the
UPS can supply.

Reduce some load and check output Load-
Capacity in specification.

Warning 16:OverLoadLock

The connected devices are
demanding more power than the
UPS can supply. UPS will transfer to
bypass mode from line mode.

Reduce some load and check output Load-
Capacity in specification.

Warning 17:EpoActive

Check the EPO connector.

Check if the connector is loose when EPO
acts abnormally.

Warning 18:MaintainOpen

The UPS is in maintenance mode.

Check if external maintenance bypass

signal port is not connected to 2-pin EPO

port on the optional controller module
when it acts abnormally.

7 T R O U B L E SH O OT I N G

Summary of Contents for PowerValue RT G2

















































Search results

Summary of Contents for PowerValue RT G2

Reviews:

Brands by name

Popular brands

ABB PowerValue RT G2, User Manual

Search results

Summary of Contents for PowerValue RT G2

Reviews:

Brands by name

Popular brands