manualshive.com logo in svg

ABB PowerValue RT G2, User Manual

Share
Download
ABB PowerValue RT G2 User Manual Download Page 28

28

A B B U PS PRODUC TS A N D SOLUTI ON S

Y

Yi

i_

_L

Li

iu

u

2

20

02

22

2-

-0

01

1-

-2

21

1

Bat Test Mode M

IP1: 120.0V/49.9Hz

IP2: 120.0V/49.9Hz

OP1:120.5V/49.9Hz

OP2:120.5V/49.9Hz

  Bat:  97.8V/97.0V

Load:  0/   0/  ----%

Back    Time:   13H

—
Table : Battery Test Type

Short Time

10-second test time

Long Time

12 second (default), can be set up from 12-54 second

Long Time

10 min (Fault) , can be set up from 1~99min

Till to Bat Low

Test until battery is low voltage

However, it could execute this test in Line/CVCF(Converter) mode and reminder will pop up in the 
screen. When “Yes” is selected, the screen will return back to home page with “Battery Test Mode” 
displayed on top. If the test is completed, the displayed status will change back to UPS current mode. 
There are four battery test types to select. Refer to below table.

b) On Battery Test mode, it will display “Cancel Test” in control menu. When “Cancel Test” is selected, 
the screen will change back to UPS current mode.

3) 

Turn to Bypass

If it is selected and confirmed, the UPS will transfer from Line mode to Bypass mode. 

Y

Yi

i_

_L

Li

iu

u

2

20

02

22

2-

-0

01

1-

-2

21

1

: 

Turn On

      Cancel Test

            Turn To Bypass

SR On

        Charger On

 Control:

Y

Yi

i_

_L

Li

iu

u

2

20

02

22

2-

-0

01

1-

-2

21

1

Turn On

  Bat  Test

            Turn To Bypass

SR Off

        Charger Off

 Control:

YYii__LLiiuu

22002222--0011--2

21

1

Cancel Test ?

: 

 Yes

No

YYii__LLiiuu

2200222

2-

-0

01

1-

-2

21

1

Turn To Bps ?

 Yes

No

Y

Yi

i_

_L

Li

iu

u

2

20

02

22

2-

-0

01

1-

-2

21

1

Line  Mode M

IP1:120.0V/60.0Hz

IP2:120.0V/60.0Hz

OP1:120.5V/60.0Hz

OP2:120.5V/60.0Hz

  Bat:  120.0/120.0V

Load:  0/   0/  ----%

Y

Yi

i_

_L

Li

iu

u

2

20

02

22

2-

-0

01

1-

-2

21

1

Bypass  Mode M

IP1:122.6V/49.9Hz

IP2:122.6V/49.9Hz

OP1:120.5V/49.9Hz

OP2:120.5V/49.9Hz

  Bat:  97.8V/97.0V

Load:  0/   0/  ----%

Summary of Contents for PowerValue RT G2



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands