ABB PowerValue RT G2 User Manual Download

Page: 42 / 50

A B B U PS PRODUC TS A N D SOLUTI ON S

LCD Message

Explanation

Solution

Fault 23:Op STS Open

Output relay or STS is open.

Contact service personnel.

Fault 24:Op STS Short

Output relay or STS is short
circuited.

Contact service personnel.

Fault 25:Wiring Fail

The wiring is wrong.

Contact service personnel.

Fault 26:Bat Fuse Open

Battery fuse is broken.

Contact service personnel.

Fault 27:Charge Short

The battery is short circuited.

Contact service personnel.

Fault 31:Para Comm Fail

The communication between UPS
modules is interrupted.

Contact service personnel.

Fault 32:Host Line Fail

The host line between UPS modules
fails.

Contact service personnel.

Fault 33:OP Curr Unbal

The load share line between UPS
modules fails.

Contact service personnel.

Fault 34:Ver Incompat

The firmware version between UPS
modules is incompatible.

Contact service personnel.

Fault 41:DSP Comm Fail

The internal communication in UPS
module is interrupted.

Contact service personnel.

Fault 42:Over load

Heavy overload causes UPS fault.

Reduce some load.

Fault 43:Charger Fail

Battery polarity is connected
reversely or charger voltage is
abnormal.

Contact service personnel.

Fault 44:Model Fault

UPS model is not able to identify.

Contact service personnel.

Fault 45:Mcu Comm Fail

As stated.

Contact service personnel.

Fault 46:CT Satiation

Load current sensor is abnormal.

Contact service personnel.

Fault 47:Fan Fault

The two fans are stuck or broken.

Make sure fans work well when UPS is
working.

Warning 01:BatLow

Battery voltage is low.

Charge the battery when the mains is
normal.

Warning 02:BatOpen

Battery is not connected.

Check battery breaker status.

Check if the battery connection is
well connected.

Check the setting of Nominal Battery
voltage.

Contact service personnel if
necessary

Warning 03:BatPhaseLoss

The voltage between positive and
negative battery is different.

Check the battery connection.

Warning 04:LineIpNLoss

Neutral loss

Check if the Neutral connection is well and
contact service personnel.

Warning 05:LinePhaseError

As stated.

Check if the Mains phase sequence is
correct and contact service personnel.

Summary of Contents for PowerValue RT G2

















































Search results

Summary of Contents for PowerValue RT G2

Reviews:

Related manuals for PowerValue RT G2

Brands by name

Popular brands

ABB PowerValue RT G2, User Manual

Search results

Summary of Contents for PowerValue RT G2

Reviews:

Related manuals for PowerValue RT G2

Brands by name

Popular brands