ABB MultiMove Applications Manual Download Page 47

Page: 47 / 110

4 Calibration

4.4.3. Example "SyncSpot"

3HAC021272-001 Revision: H

ght

200

4-2008 ABB.

4.4.3. Example "SyncSpot"

About this example

In this example, the world coordinate system and the base coordinate system for the handle

robot are identical.

The base coordinate system for the process robot is defined. An object coordinate system is

defined to be fixed to the work object held by the handle robot.

Illustration

xx0300000593

Coordinate systems

Item

Description

Process robot

Handle robot

World coordinate system

Base coordinate system for the handle robot

Base coordinate system for the process robot

User coordinate system for the process robot (same as tool0 coordinate
system for handle robot)

Object coordinate system for the process robot

Summary of Contents for MultiMove





































































































Search results

Summary of Contents for MultiMove

Reviews:

Related manuals for MultiMove

Brands by name

Popular brands

ABB MultiMove, Applications Manual

Search results

Summary of Contents for MultiMove

Reviews:

Related manuals for MultiMove

Brands by name

Popular brands