background image

17

General installation procedure

All required permits to agree with the local rules are granted
The AC input cable is available

Tools for installation

There is no voltage on the AC input cable during the complete 
installation procedure

Table 10: Preliminary requirements

Procedure

1. Unpack the EVSE
2.  Prepare the site. Refer to chapte

Site preparation,  

page 18.

3.  Do the mechanical installation. Refer to sectio

General 

mechanical installation procedure, page 19.

4.  Do the electrical installation. Refer to sectio

General 

electrical installation procedure, page 21.  

5. Install the cabinet cover.
6.  Do the commissioning procedure. Refer to chapter 

General commissioning procedure, page 28.

Unpack the EVSE

1. Open the box.
2.  Take out the EVSE and including parts like QSG  

from the box. 

3. Remove all packaging material from the EVSE.
4. Discard the packaging material.
5.  Make sure that all parts are delivered according to the 

order. Refer to the order and sectio

In the box on the 

previous page.

6.  Do an inspection of the EVSE and the parts for installation 

for damage.

7.  If you find damage or the parts are not according to the 

order, contact the local representative of the 
manufacturer (ABB E-mobility B.V.) refer to section 

Manufacturer and contact data at the end of the 
document.

TA B L E  O F  CO N T EN T S

P R E V I O US  C H A P T ER

N E X T  C H A P T ER

Summary of Contents for InCharge Terra AL2-40-240-T1-WC1R








































Reviews: