ABB HT611658 Operation Manual Download

Page: 104 / 148

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.10 Fitting the spinner nose cone

HZTL4033_EN

Rev.K

January 2022

9.10

Fitting the spinner nose cone

If present:

The spinner nose cone (25012) and Loctite®542 are supplied by the ABB service station to-
gether with the overhauled cartridge group.

CAUTION

Total failure of turbocharger

If the spinner nose cone (25012) is not fitted correctly, or the socket screw
(25013) is not correctly tightened, the spinner nose cone can work loose dur-
ing operation and cause total failure of the turbocharger.

Follow the assembly instructions.

Always use a new socket screw (25013) and washer (25014) from the cus-
tomer spare part set (97070).

Only use new Loctite®542 supplied by the ABB service station.

Observe and note down control dimension Z.

Fig. 58: Preparing the threaded stud (25008)

Product

Size

A170-M

A175-M

M10

Table 42: Inner thread size (25008)

1. Remove residual glue from the inner thread of the threaded stud (25008) by using a

screw tap.

2. Clean and degrease the inner thread of the threaded stud and socket screw (25013).

Page

102

146

Summary of Contents for HT611658



















































































































































Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands

ABB HT611658, Operation Manual

Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands