ABB HT611658 Operation Manual Download

Page: 61 / 148

Operation Manual / A170-M.. - A175-M..

7 Periodic maintenance / 7.4 Cleaning the compressor during operation

HZTL4033_EN

Rev.K

January 2022

7.4.3

Principle of wet cleaning

To clean the compressor stage during operation, water is injected before the compressor
wheel.

The water does not act as a solvent. The coating is removed by the mechanical action of the
impacting droplets. The process is particularly suitable as long as the contamination is not
too advanced.

CAUTION

Corrosion and deposits when cleaning

Salt water and cooling water treatment substances damage and adversely
affect turbocharger parts.

Never use salt water, but only pure water for cleaning.

CAUTION

Volume of water

Uncontrolled volumes of water can damage the turbocharger and the en-
gine.

Never connect the water line without the orifice specified for the tur-
bocharger.

Page

146

Summary of Contents for HT611658



















































































































































Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands

ABB HT611658, Operation Manual

Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands