ABB HT611658 Operation Manual Download

Page: 98 / 148

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.8 Installing the nozzle ring

HZTL4033_EN

Rev.K

January 2022

Installing cover ring

Fig. 52: Installing cover ring

Product

Size

Tightening torque [Nm]

A170-M

M14

130

A175-M

M16

200

Table 38: Tightening torque (57005)

1. Using lifting gear, move in cover ring (57001) over guide studs (90802) with notch (V) fa-

cing the gas outlet flange until the lifting gear is on the gas outlet casing.

2. Fit guide plates (90328) with nuts (61037).

3. Remove the lifting gear.

4. Slide in cover ring as far as it will go.

5. Remove guide plates (90328) and nuts (61037).

6. Coat threads of screws (57005) with high-temperature grease.

7. Fit and tighten screws (57005).

Page

146

Summary of Contents for HT611658



















































































































































Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands

ABB HT611658, Operation Manual

Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands