ABB HT569038 Operation Manual Download

Page: 74 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

6 Periodic maintenance work / 6.2 Cleaning components mechanically

HZTL4030_EN

Revision D

May 2017

Repeat the soaking and brushing if necessary.

Use clean water to remove all traces of solvent from parts.

Dry components completely.

Spray cleaned surfaces with penetrating oil. Do not spray the outer surfaces of the tur-
bocharger.

Dispose of contaminated water and cleaning agents in accordance with the information
in the material safety data sheet.

6.2.5

Cartridge group, general

CAUTION

Corrosion

If the cartridge group is not put back into operation immediately after clean-
ing, parts may corrode.

Immediately after cleaning, install the cartridge group and put it back
into operation.

Compressor wheels can be heavily contaminated due to poorly filtered suction air; turbines
can be heavily contaminated due to coked oil. Contamination such as this must be removed
during the standard service intervals (see service work chapter).

Remove turbocharger from engine (see chapter

Removing and Installing

→

Remove cartridge group (see chapter

Dismantling and fitting

→

First clean the compressor end and then the turbine end according to the following descrip-
tion.

Page

Summary of Contents for HT569038



























































































































Search results

Summary of Contents for HT569038

Reviews:

Related manuals for HT569038

Brands by name

Popular brands

ABB HT569038, Operation Manual

Search results

Summary of Contents for HT569038

Reviews:

Related manuals for HT569038

Brands by name

Popular brands