ABB HT569038 Operation Manual Download

Page: 121 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

Tables

HZTL4030_EN

Revision D

May 2017

Tables

Table 1: Related documents .......................................... 3

Table 2: Weights of turbochargers A130-H.. – A140-
H......................................................................................... 8

Table 3: Requirements for threaded rods ................ 14

Table 4: Tightening torques for standard nuts....... 16

Table 5: Pressure screw tightening torque .............. 18

Table 6: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 25

Table 7: Lubricating oil temperature at the inlet ... 26

Table 8: Lubricating oil temperature at the outlet 26

Table 9: Tightening torque (86505).......................... 30

Table 10: Expected replacement intervals ............... 37

Table 11:

Value table for soaking

.............................. 46

Table 12: Malfunctions when starting – Delayed
start-up .......................................................................... 49

Table 13: Malfunctions when starting – Vibrations 49

Table 14: Malfunctions when starting – Rubbing of
rotating parts................................................................ 49

Table 15: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 50

Table 16: Malfunctions during operation – Speed re-
duces............................................................................... 50

Table 17: Malfunctions during operation – Speed in-
creases ........................................................................... 50

Table 18: Malfunctions during operation – Exhaust
gas temperature too high ........................................... 51

Table 19: Malfunctions during operation – Charge air
pressure too low............................................................ 51

Table 20: Malfunctions during operation – Charge
air pressure too high ................................................... 52

Table 21: Malfunctions during operation – Engine
performance losses ..................................................... 52

Table 22: Malfunction – Turbocharger pumping .... 53

Table 23: Malfunction – Sporadic surge blows ....... 53

Table 24: Malfunctions when stopping – Runout
noises.............................................................................. 54

Table 25: Malfunctions when stopping – Runout
time too short ............................................................... 54

Table 26: Malfunction of the speed measurement
system – No signal or poor signal amplitude .......... 55

Table 27: Malfunction of the speed measurement
system – Measured speed too high ........................... 55

Table 28: Malfunction of the speed measurement
system – Measured speed too low............................. 55

Table 29: Swivel lifting eyes......................................... 58

Table 30: Ring nuts to be used.................................... 58

Table 31: Weights of assemblies................................. 59

Table 32: 3 press-off screws ........................................ 62

Table 33: 6 press-off screws – gas outlet flange..... 63

Table 34: Permissible clearances A and B .................. 71

Table 35: Permitted nozzle ring compression PD ... 72

Table 36: End position of the nozzle ring, control di-
mension H ....................................................................... 74

Table 37: Tightening torque (51007).......................... 75

Table 38: Tightening torque (79041) ......................... 76

Table 39: Tightening torque (72011) .......................... 77

Table 40: Permissible clearances N and R ................ 78

Table 41: Tightening torque (72020).......................... 79

Table 42: Tightening torque (51009) ......................... 80

Table 43: Tightening torques of the screw fittings 81

Table 44: Customer spare part set 97070 ................ 87

Table 45: Spare parts list ............................................. 89

Page

Summary of Contents for HT569038



























































































































Search results

Summary of Contents for HT569038

Reviews:

Related manuals for HT569038

Brands by name

Popular brands

ABB HT569038, Operation Manual

Search results

Summary of Contents for HT569038

Reviews:

Related manuals for HT569038

Brands by name

Popular brands