ABB HT569038 Operation Manual Download

Page: 110 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

8 Dismantling and fitting / 8.18 Installing the gas outlet flange

HZTL4030_EN

Revision D

May 2017

8.18

Installing the gas outlet flange

Fig. 49: Installing the gas outlet flange

1. If present: Insert the metal C-ring (57003) into the turbine casing (51000) and secure with

high-vacuum grease.

2. Install the gas outlet flange (57002) in the turbine casing.

3. Measure radial clearance (R) (see chapter Radial clearances N and R).

8.19

Installing the gas outlet casing

Fig. 50: Installing the gas outlet casing

Part number

A130

A135

A140

51009

20 Nm

M10

40 Nm

M12

65 Nm

Table 42: Tightening torque (51009)

1. Insert a new gasket (61002) into the gas outlet casing (61001).

2. Coat the threads of the studs (51008) with high-temperature grease.

3. Attach the lifting gear to the gas outlet casing (61001) and position the gas outlet casing

in the correct position on the turbine casing (51000).

4. If present: Fit the support (61301).

Page

Summary of Contents for HT569038



























































































































Search results

Summary of Contents for HT569038

Reviews:

Related manuals for HT569038

Brands by name

Popular brands

ABB HT569038, Operation Manual

Search results

Summary of Contents for HT569038

Reviews:

Related manuals for HT569038

Brands by name

Popular brands