ABB HT569038 Operation Manual Download | Manualshive

Page: 43 / 122

background image

Operation Manual / 4 Product description / A130-H.. - A140-H

2 Removing and Installing / 2.3 Installing the turbocharger

© Copyright 2017 ABB. All rights reserved.

HZTL4030_EN

Revision D

May 2017

2.3

Installing the turbocharger

2.3.1

Inserting gaskets

CAUTION

Inserting the gaskets

Gaskets that are forgotten, damaged or improperly inserted will lead to oil
leaks.

u

Always use new gaskets and insert them carefully into the slot.

The oil is supplied (02) and drained (03) through the bracket (01).

The necessary sealing is provided by O-rings. The O-rings are not included in the ABB Turbo
Systems scope of delivery.

Fig. 9: Inserting gaskets into the bracket

01 Bracket

04 Slot for O-ring

02 Oil supply

05 O-rings

03 Oil drain

06 Pin (optional)

Pin (06) as installation safety device

Turbochargers can have an oil inlet either on their right or left side; the oil inlet position can
be different for the turbocharger fitted on the left and on the right engine bank.

A pin can be installed in every support as an installation safety device to prevent inadvertent
incorrect fitting. This pin fits into the respective slot on the foot of the bearing casing. In-
structions of the enginebuilder must be observed.

Page

13

/

91

«
...
41
42
43
44
45
...
»

Summary of Contents for HT569038



























































































































Reviews:

No comments

Related manuals for HT569038

Battery Charger

Brand: Vanair Pages: 14

Brand: Icom Pages: 2

Brand: Lab599 Pages: 12

Brand: BASETech Pages: 8

Brand: Hama Pages: 75

WAECO PerfectCharge CA360

Brand: Dometic Pages: 304

Brand: Fronius Pages: 64

FLASH CHARGE 92136-0920

Brand: Tyco Pages: 2

Brand: Metabo Pages: 16

Brand: Stanley Pages: 156

PSC-12100-B04-CE

Brand: AlarmSaf Pages: 2

Brand: Aegis Pages: 2

Brand: LXE Pages: 60

Brand: Laser Pages: 2

Brand: KAFULLE Pages: 4

Brand: Hama Pages: 40

Brand: Control 4 Pages: 4

Brand: NATURE & DECOUVERTES Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands