manualshive.com logo in svg

ABB FEP315, Original Instruction

Share
Download
ABB FEP315 Original Instruction Download Page 38

Commissioning 

 

36 - EN 

FEX300, FEX500 

SM/FEX300/FEX500/FM/CSA-EN 

 

7.4 

Changing the type of protection 

 

Models FEP315 / FEP515, FEH315 / FEH515, FEP325 / FEP525, FET325 / FET525 can 
provide various types of protection during operation: 
•  When connected to an intrinsically safe circuit in Div. 1, operated as an intrinsically safe 

device 

•  When connected to a non-intrinsically safe circuit in Div. 1, operated as a device with a 

flameproof enclosure 

•  When connected to a non-intrinsically safe circuit in Div. 2, operated as a non-sparking 

device 

If a device which is already operational is required to provide a different type of protection, the 
following measures must be implemented/insulation checks must be performed in accordance 
with FM3600-ff. 
A subsequent change of the type of protection is the sole responsibility of the operator. 
 

No.  1. Type of protection 

2. Type of protection 

Required step/check 

1 Div. 

1: 

Device with flameproof 
enclosure, non-intrinsically-
safe circuit 

Div. 1: 
Intrinsically safe circuits 

•  Switch off supply power. 

Use 500 VAC or 710 VDC to take the following 
measurements for one minute: 
Jumper terminals 31/32, 41/42, 51/52, 81/82. 
Then measure all jumpers (A,B,C,D) against one 
another. 

3

1

3

2

4

1

4

2 51 52

8

1

8

2

A

B

C

D

G00884

 

 

 

•  Switch off supply power. 

Use 500 VAC or 710 VDC to take the following 
measurements for one minute: 
Jumper terminals 31/32, 41/42, 51/52, 81/82. 
Then measure against the housing. 

  

 

• 

Visual 

inspection 

  

Div. 

2: 

Non-sparking 

•  Special precautions/checks are not necessary. 

2 Div. 

1: 

Intrinsically safe circuits 

Div. 1: 
Device with flameproof 
enclosure, non-
intrinsically-safe circuit 

•  Visual inspection (no damage to the threads of 

the cover or the cable fittings) 

  

Zone 

2: 

Non-sparking 

•  Special precautions/checks are not necessary. 

3 Div. 

2: 

Non-sparking 

Div. 1: 
Intrinsically safe circuits 

•  Perform the checks described under No. 1. 

  

Div. 

1: 

Device with flameproof 
enclosure, non-
intrinsically-safe circuit 

•  Visual inspection (no damage to the threads of 

the cover or the cable fittings) 

 

 

 

3

1

3

2

4

1

4

2 51 52

8

1

8

2

G0088

5

Summary of Contents for FEP315

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands