manualshive.com logo in svg

ABB FEP315, Original Instruction

Share
Download
ABB FEP315 Original Instruction Download Page 27

 

Ex relevant specifications for operation in Div. 1

 

SM/FEX300/FEX500/FM/CSA-EN 

FEX300, FEX500 

EN - 25 

 

5.3 

Temperature data for operation in Zone 1 / Div. 1 

 

 

Model name 

Surface temperature 

FEP315 / FEH315 
FEP515 / FEH515 

70 °C (158 °F) 

FEP325 / FEP525 

85 °C (185 °F) 

FET325 / FET525 

70 °C (158 °F) 

 

 

 
The surface temperature depends on the fluid temperature. 
With increasing fluid temperature > 70 °C (158 °F) or > 85 °C (185 °F) the surface temperature also increases to the level of the fluid 
temperature. 
 

 

Note 

The maximum permissible fluid temperature depends on the lining and flange material, and is limited by the operating values in Table 1 and the 
explosion protection specifications in Tables 2 ... n. 
 

 

Table 1: Fluid temperature as a function of lining and flange material 

 

Models FEP315 / FEP325, FEP515 / FEP525 

 

Materials 

Fluid temperature (operating values) 

Lining 

Flange 

Minimum 

Maximum 

Hard rubber 

Steel 

-10 °C (14 °F) 

-5 °C (23 °F) 

1)

 

90 °C (194 °F) 

80 °C (176 °F) 

1)

 

Hard rubber 

Stainless steel 

-15 °C (5 °F) 

-5 °C (23 °F) 

1)

 

90 °C (194 °F) 

80 °C (176 °F) 

1)

 

Soft rubber 

Steel 

-10 °C (14 °F) 

60 °C (140 °F) 

Soft rubber 

Stainless steel 

-15 °C (5 °F) 

60 °C (140 °F) 

PTFE 

Steel 

-10 °C (14 °F) 

130 °C (266 °F) 

PTFE 

Stainless steel 

-25 °C (-13 °F) 

130 °C (266 °F) 

PFA 

Steel 

-10 °C (14 °F) 

180 °C (356 °F) 

PFA 

Stainless steel 

-25 °C (-13 °F) 

180 °C (356 °F) 

Thick PTFE 

Steel 

-10 °C (14 °F) 

180 °C (356 °F) 

Thick PTFE 

Stainless steel 

-25 °C (-13 °F) 

180 °C (356 °F) 

ETFE 

Steel 

-10 °C (14 °F) 

130 °C (266 °F) 

ETFE 

Stainless steel 

-25 °C (-13 °F) 

130 °C (266 °F) 

 

1) 

Only China production site 

 

 

Models FEH315, FEH515 

 

Lining 

Process connection 

Material 

Fluid temperature (operating values) 

 

 

 

Minimum 

Maximum 

PFA 

Flange 

Stainless steel 

-25 °C (-13 °F) 

180 °C (356 °F) 

PFA 

Wafer type 

- 

-25 °C (-13 °F) 

130 °C (266 °F) 

PFA 

Variable process connection 

Stainless steel 

-25 °C (-13 °F) 

130 °C (266 °F) 

 

 

 

Summary of Contents for FEP315

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands