ABB AX416 User Manual Download Page 36

Page: 36 / 72

…5

PROGRAMMING

5.5

Configure Alarms

Configure Alarm 1

Alarms 2 and 3 configuration (and Alarms 4 and 5 if option board fitted

and

analog features enabled – see Section 7.3) is identical to Alarm 1
configuration.
Alarm 3 can also be configured as a Wash alarm if

A3: Type

is set to

Wash

–

see following frame.

Alarm 1 Type

Select the type of alarm required:

Off

– The alarm is disabled, the alarm LED is off and the relay is de-energized

at all times.

Alarm

– The analyzer is configured using the

Assign

frame (following) to

generate an alarm in response to a specified high or low pH,
Redox (ORP) or process temperature sensor reading.

Status

– An alarm is generated if either a power failure or a condition that causes

any of the error messages in Table 8.1 (page 62) to be displayed
occurs.

Wash

– Alarm 3 is configured to control the wash sequence.

Note.

The

Wash

alarm type can be assigned only to Alarm 3 and is displayed only when

the lower display line shows

A3: Type

A1: Type

set to

Off

Status

A1: Type

set to

Alarm

– continued below.

A3: Type

set to

Wash

– see Section 5.5.1.

Alarm 1 Assign

Select the alarm assignment required:

Sen.A

– The analyzer activates an alarm if the pH or Redox (ORP) value of the process

Sen.B

fluid measured by the selected sensor exceeds or drops below the value set
in the

Alarm 1 Set Point

parameter, depending on the type of

Alarm 1 Action

selected – see next page.

Temp.A

– The analyzer activates an alarm if the temperature of the process fluid

Temp.B

measured by the selected sensor exceeds or drops below the value set in
the

Alarm 1 Set Point

parameter, depending on the type of

Alarm 1 Action

selected – see next page.

A–B

– The analyzer activates an alarm if the difference between the Sensor A and

Sensor B readings exceeds or drops below the value set in the

Alarm 1 Set

Point

parameter, depending on the type of

Alarm 1 Action

selected – see

next page.

Note.

The

Sen.B

Temp.B

and

A–B

alarm assignment types are applicable only to dual

input analyzers and

A–B

is displayed only when

Probe Type

for each sensor is set to

–

see Section 5.3.

Continued on next page.

Config. Alarm 1

-----

A1: Type

-----

A1: Assign

-----

CONFIG. ALARMS

-----

Wash

Status

Alarm

Off

A-B

Temp.B

Sen.B

Temp.A

Sen.A

A1: Failsafe

Config. Alarm 2

A1: Assign

Config. Alarm 1

Wash Mode

Summary of Contents for AX416









































































Search results

Summary of Contents for AX416

Reviews:

Related manuals for AX416

Brands by name

Popular brands

ABB AX416, User Manual

Search results

Summary of Contents for AX416

Reviews:

Related manuals for AX416

Brands by name

Popular brands