ABB AX416 User Manual Download Page 31

Page: 31 / 72

PROGRAMMING…

5.2

Configure Display

Set Language

Sets the language to be used on all displays.

Language Page

Use the

and

keys to select the required language.

Set Temperature Units

Temperature Units

Use the

and

keys to select the sample temperature display units.

Set Up Display Backlight

Backlight

Use the

and

keys to select the required backlight option:

Auto.

–

Backlight comes on at each button press and switches off one minute after
the last button press.

–

Backlight is always on.

Return to main menu.

See Section 5.3.

CONFIG. DISPLAY

-----

Set Language

-----

Temp. Units

-----

Off

Set Temp. Units

-----

Deg. F

Deg. C

LED Backlight

-----

Set Backlight

-----

Auto.

CONFIG. DISPLAY

CONFIG. SENSORS

Set Backlight

Set Language

Set Temp. Units

English

Deutsch

Francais

Espanol

Italiano

Summary of Contents for AX416









































































Search results

Summary of Contents for AX416

Reviews:

Related manuals for AX416

Brands by name

Popular brands

ABB AX416, User Manual

Search results

Summary of Contents for AX416

Reviews:

Related manuals for AX416

Brands by name

Popular brands