manualshive.com logo in svg

ABB ACH550 series, Installation Manual

Share
Download
ABB ACH550 series Installation Manual Download Page 21

Installation of the module

21

Installing the router module to the ACH550 drive with the E-Clipse 
Bypass option (US only) 

This section describes how to install the router module to the drive 
when the E-Clipse Bypass option is used. 

The ACH550 drive with the E-Clipse Bypass option (US only) is an 
ACH550 AC-adjustable-frequency drive in an integrated package 
with a bypass motor starter. For more information, see 

E-Clipse 

Bypass Configurations for ACH550 Drives User’s Manual 
(3AUA0000016461 [English]).

WARNING!

 Before installation, switch off the drive power supply. 

Wait at least five minutes to ensure that the capacitor bank of the 
drive is discharged. Switch off all dangerous voltages connected 
from external control circuits to the inputs and outputs of the drive. 

Note: 

Do not connect the router module to the network before you 

have commissioned the device!

1. Before installation, switch off the drive power supply for at least 

5 minutes to discharge the capacitor bank of the drive. For 
more information, refer to 

Safety instructions

 on page 5.

2. Remove the plug connected to the X1 terminal of the drive.

 

Summary of Contents for ACH550 series











































Reviews:

No comments

Brands by name

Popular brands

Load more brands