manualshive.com logo in svg

ABB ACH550 series, Installation Manual

Share
Download
ABB ACH550 series Installation Manual Download Page 16

Installation of the module

16

Installing the router module to the ACH550 drive

This section describes the necessary steps to install the router 
module to the drive.

WARNING!

 Before installation, switch off the drive power supply. 

Wait at least five minutes to ensure that the capacitor bank of the 
drive is discharged. Switch off all dangerous voltages connected 
from external control circuits to the inputs and outputs of the drive. 

Note: 

Do not connect the router module to the network before you 

have commissioned the device!

1. Before installation, switch off the drive power supply for at least 

5 minutes to discharge the capacitor bank of the drive. For 
more information, refer to 

Safety instructions

.

2. To connect the 
MS/TP cable to the 
Embedded 
Fieldbus (EFB) 
connectors of the 
drive, install the 
MS/TP cable as 
shown in the 
figure. 

Note: 

Do not connect the cable shield to the drive! 

For example connections, see 

ACH550 BACnet Protocol Manual

 

(3AUA0000004591 [English]), chapter 

Installation

, section 

Hardware installation

.

Connect the wires in the order listed in the table below.

RBIP-01 terminal

ACH550 terminal 

Wire

B (+)

29, B (+)

orange

A (-)

30, A (-)

white

AGND 31, 

AGND

blue

Summary of Contents for ACH550 series











































Reviews:

No comments

Brands by name

Popular brands

Load more brands