Aastra AT-200HT Owner's Owner'S Manual Download Page 12 | Manualshive

Page: 12 / 28

background image

4. Press and hold the

ERASE

button, then press the review

"#

button while in Stand-By Screen mode.

Installing the Belt Clip

A belt clip has been supplied with your headset telephone. It
can be easily installed or removed as required. See Figure 1

1. Insert the belt clip mounting tabs into the corresponding

mounting holes located on the rear surface of the unit.

2. Confirm the belt clip mounting tabs are aligned correctly.

3. Press the belt clip to the left to lock it in place.

Using the Headset

Your AT-200HT is supplied with a high quality headset to
provide clear voice communications. Its microphone boom can
be swiveled so the headset can be used on either ear. See
Figures 3 & 4

1. Plug from the headset cord into the modular jack marked

HEADSET

on the left side of the unit.

2. Place the headband on your head with the cushioned

speaker over the ear of your preference.

10

«
...
10
11
12
13
14
...
»

Summary of Contents for AT-200HT Owner's





























Reviews:

No comments

Related manuals for AT-200HT Owner's

Univerge SV9100

Brand: NEC Pages: 6

Univerge SV9100

Brand: NEC Pages: 10

Univerge UM8000

Brand: NEC Pages: 7

Brand: NEC Pages: 46

Brand: NEC Pages: 39

Brand: NEC Pages: 5

Brand: NEC Pages: 150

Univerge SV9100

Brand: NEC Pages: 77

Brand: NEC Pages: 56

Brand: Samsung Pages: 2

Brand: Barracuda Pages: 3

Brand: Walton Pages: 16

Brand: switel Pages: 88

Brand: Radio Shack Pages: 24

Brand: Alcatel Pages: 64

Brand: GE Pages: 60

Brand: Swisscom Pages: 110

Brand: GE Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands