Aastra AT-200HT Owner's Owner'S Manual Download Page 27

Page: 27 / 28

Troubleshooting

No Dial Tone.

•

The telephone line cord is not plugged in properly at the
telephone jack or at the telephone.

•

Test the telephone using a different telephone jack, if it works,
the first jack may be defective.

Have Dial Tone but Cannot Dial Out.

•

Check that the

PULSE/T

ONE switch is set to the correct mode.

Display screen is blank.

•

Check if the batteries have been installed correctly.

•

The batteries need to be replaced.

Unable to Set Display Language.

•

"SET LANGUAGE"

is displayed for sixteen seconds after the bat-

teries are installed. If you have not completed the setup procedure,
the display will return to Stand-By Screen mode. Press and hold
the

ERASE

button, then press the review

button. The display

Language, or Area Code can now be programmed or changed.

Does not display Caller-ID information.

•

Confirm that your local telephone company has activated
Caller-ID service.

•

Caller-ID information is sent by the telephone company be-
tween the first and second rings. If the call is answered before
the second ring, the Caller-ID information may not be received
correctly.

Summary of Contents for AT-200HT Owner's





























Search results

Summary of Contents for AT-200HT Owner's

Reviews:

Related manuals for AT-200HT Owner's

Brands by name

Popular brands

Aastra AT-200HT Owner's, Owner'S Manual

Search results

Summary of Contents for AT-200HT Owner's

Reviews:

Related manuals for AT-200HT Owner's

Brands by name

Popular brands