background image

3.8 TONNE 

2 Post Baseplate Hoist 

OPERATING  INSTRUCTIONS 

The hoist should only be operated by personnel that have 

been thoroughly trained in operation and maintenance of 
the hoist. 

1.

Position the vehicle between the columns, turn off the
engine and apply the park brake.

2.

Adjust the lifting arms until they reach the supporting
position of the vehicle.

Note: It is important that the vehicle is evenly balanced on

the hoist.

3.

Make sure that all personnel are clear and there are no

obstructions around the hoist.

TO RAISE THE HOIST

1.

Turn the power on.

2.

Press the “UP” button on the control box.

3.

Raise the hoist to approximately 500mm, stop and check
that the lifting pads are evenly supporting the lifting

positions of the vehicle.

4.

Continue raising the hoist to the desired working height

checking for any obstructions. 

5.

Once the hoist has reached the desired working height lower

the hoist onto the safety locks by means of pushing the
lowering leaver on the hydraulic power unit.

Note: Check for correct engagement on the locks.

TO LOWER THE HOIST

1.

Raise the hoist 100mm or until the locks are clear.

2.

Pull the locking leaver to disengage the locks.

3.

Lower the hoist by means of pushing on the lowering
lever. 

Note:  Check for any obstructions under the hoist

when lowering.

4.

When the vehicle is lowered to the lowest position

swing the lifting arms away from the vehicle to the rest
position.  Turn off the power.

MODEL: 

AL-6254 

SERIAL NO.: 

APPROVALS: 

WAH19926 

Design Code: AS1418.9 -1996 

Summary of Contents for AL-6254A




































Reviews: