Aanderaa DCPS 5400 Operating Manual Download Page 21

Page: 21 / 150

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

Page 21

Temperature

Float

The temperature in degree centigrade. The value is used for

calculation of Salinity, Sound speed and Density. Can be

altered while sensor is running to compensate for variable

temperature.

No /

Low

Enable Derived

Sound Speed

BOOL 1

If enabled it will calculate the sound speed from the other

available sensors or fixed values. This overrides the Sound

Speed setting. If a parameter is available from another sensor it

will use this in the calculation, otherwise it will use the fixed

value.

Pressure Sensor Id

ENUM 1

When the DCPS is connected to AiCaP, a list of other available

sensors connected to the SmartGuard/SeaGuard Datalogger is

shown. This makes it possible to get a correct depth input from

another sensor through the datalogger

Only in AiCaP mode

Pressure Parameter

ENUM 1

A list of all available Pressure parameters with kPa as unit is

shown in the dropdown menu. Make sure that the correct

pressure parameter is selected. Only in AiCaP mode.

Air Pressure Sensor

ENUM 1

When the DCPS is connected to AiCaP, a list of other available

sensors connected to the SmartGuard/SeaGuard Datalogger is

shown. This makes it possible to get a correct air pressure input

from another sensor through the datalogger

Only in AiCaP

mode

Air Pressure

Parameter Id

ENUM 1

A list of all available Air Pressure parameters with hPa or mbar

as unit is shown in the dropdown menu. Make sure that the

correct pressure parameter is selected. Only in AiCaP mode.

Temperature Sensor

ENUM 1

When the DCPS is connected to AiCaP, a list of other available

sensors connected to the SmartGuard/SeaGuard Datalogger is

shown. This makes it possible to get a correct temperature input

from another sensor through the datalogger

Only in AiCaP

mode

Temperature

Parameter Id

ENUM 1

A list of all available Temperature parameters with DegC or

Deg.C as unit is shown in the dropdown menu. Make sure that

the correct temperature parameter is selected. Only in AiCaP

mode.

Conductivity Sensor

ENUM 1

When the DCPS is connected to AiCaP, a list of other available

sensors connected to the SmartGuard/SeaGuard Datalogger is

shown. This makes it possible to get a correct conductivity input

from another sensor through the datalogger

Only in AiCaP

mode

Conductivity

Parameter Id

ENUM 1

A list of all available Conductivity parameters with mS/cm as

unit is shown in the dropdown menu. Make sure that the correct

conductivity parameter is selected. Only in AiCaP mode.

Heading Sensor Id

ENUM 1

When the DCPS is connected to AiCaP, a list of other available

sensors connected to the SmartGuard/SeaGuard Datalogger is

shown. This makes it possible to get a correct heading input

from another sensor through the datalogger

Only in AiCaP

mode

Summary of Contents for DCPS 5400























































































































































Search results

Summary of Contents for DCPS 5400

Reviews:

Related manuals for DCPS 5400

Brands by name

Popular brands

Aanderaa DCPS 5400, Operating Manual

Search results

Summary of Contents for DCPS 5400

Reviews:

Related manuals for DCPS 5400

Brands by name

Popular brands