Aanderaa DCPS 5400 Operating Manual Download Page 32

Page: 32 / 150

Page 32

July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor

Acoustic Wave

Option Key

INT

To active the Wave features you need a license key.
This key is delivered with the instrument or upgrade kit if wave is

ordered. Only available in AiCaP.

High

Select Active

Wave Cell

INT

Select cell 1, 2 or 3 for calculation of wave, Cell 1 is closest to

surface, default cell is 1. Only available in AiCaP.

Enable Fixed

Wave Depth Cell BOOL 1

If enabled you might set the distance from surface to the centre of

first wave cell in Wave Cell Center Depth. If not set the placement

of first cell will be dynamic depending on wave measurement and

depth. Only available in AiCaP.

Wave Cell Center

Depth

INT

Distance from surface to centre of first wave cell. Only available in

AiCaP.

Enable Max Tilt

Ping Discard

BOOL 1

If enabled ping with tilt above limit will not be used.

Max Tilt Limit

Ping Discard

INT

Set the tilt limit in degrees for when to discard ping. Default value is

60.

Distance

Pressure to

Center TRD

INT

Set the distance from pressure sensor reference port to centre of

transducer, This value is used to instrument depth reference to the

centre of transducer instead of pressure sensor port. Default value

is 0.187 meter.

Temp Coeff

INT

Only available if Temperature sensor 4080 is installed and

calibrated.

Doppler Current Profiler Sensor 5400/5402/5403 Specifications Refer Datasheet D 411 which is available on our web

site

http://www.aanderaa.com

or contact

[email protected]

You will find the latest versions of our documents on Aanderaa website.

1.8

Manufacturing and Quality Control

Aanderaa Data Instruments products have a record for proven reliability. With over 50 years’ experience producing

instruments for use in demanding environments around the globe you can count on our reputation of delivering the most

reliable products available.

We are an ISO 9001, ISO 14001 and OHSAS 18001 Certified Manufacturer. As a company we are guided by three

underlying principles: quality, service, and commitment. We take these principles seriously, as they form the foundation

upon which we provide lasting value to our customers.

Summary of Contents for DCPS 5400























































































































































Search results

Summary of Contents for DCPS 5400

Reviews:

Related manuals for DCPS 5400

Brands by name

Popular brands

Aanderaa DCPS 5400, Operating Manual

Search results

Summary of Contents for DCPS 5400

Reviews:

Related manuals for DCPS 5400

Brands by name

Popular brands