background image

 

Operators and Maintenance Manual 

 

Measuring module

 

EMS DAQ R02.01

 

Page 

16/18

 

 

Copyright: 

Auto & Aero Technologies Sp. z o.o. 

Mazowiecka 10/5, 20-723 Lublin, Poland  

 email: [email protected] 

  

www.aatech.pl 

 

 

The  module  does  not  contain  any  user-serviceable  parts.  Unauthorized 
repairs  or  modifications  may  result  in  permanent  damage  to  the 
equipment and void the warranty. 

If the module fails, return the device to the Manufacturer with description 
of the failure circumstances and symptoms. 

5.6.   Re-programming 

Modifications  to  the 

module’s

  settings  can  be  introduced  by  means  of 

service  software  provided  by  the  Manufacturer  and  the  dedicated 
diagnostic interface. 

The instrument

’s firmware updates are to be conducted on the basis of the 

bulletins  published  by  the  Manufacturer.  The  updates  can  be  introduced 
by  means  of  service  software  provided  by  the  Manufacturer  and  the 
dedicated diagnostic interface. 

5.7.  Spare parts 

The  module  does  not  contain  any  user-serviceable  parts.  The  user  is  not 
allowed to disassemble it nor replace any subassemblies.  

 

6.  Warranty 

1.

 

Auto & Aero Technologies Sp. z  o.o.  warrants this  product to be free 
from defects in materials and workmanship.  

2.

 

Auto & Aero Technologies Sp. z o.o. warrants proper operation of the 
product  if  it  is  used  in  accordance  with  its  intended  purpose  and  in 
accordance with the Operators and Maintenance Manual.  

3.

 

Auto  &  Aero  Technologies  Sp.  z  o.o.  warrants  this  product  for  12 
months from date of purchase. 

4.

 

Auto  &  Aero  Technologies  Sp.  z  o.o.  will,  at  its  sole  option,  repair  or 
replace  any  components  that  fail  in  normal  use.  Such  repairs  or 
replacement  will  be  made  at  no  charge  to  the  customer  for  parts  or 

Summary of Contents for EMS DAQ R02.01



















Reviews: