background image

 

Operators and Maintenance Manual 

 

Display

 

EEM AM4 FE H01

 

Page 

4/19

 

 

Copyright: 

Auto & Aero Technologies Sp. z o.o. 

Mazowiecka 10/5, 20-723 Lublin, Poland  

  email: [email protected] 

   

www.aatech.pl 

 

 

1.  General information 

This manual contains binding information, guidelines and warnings for safe 
handling and maintenance of this particular instrument before installation, 
during  installation  and  in  its  operating  phase.  This  document  does  not 
contain rules and guidelines on operation of aircraft instruments at large. 

Read  the  manual  thoroughly  before  turning  on  the  instrument  and 
precisely  follow  the  instructions  to  install  and  configure  it.  This  manual 
does  not  replace  instructions  on  installation,  maintenance  and  operation 
of  this  device  in  a  particular  airframe  -  these  are  to  be  prepared  by  the 
user. Instructing the pilots and maintenance personnel on operation of the 
instrument is also the responsibility of the user. 

Operation  of  this  instrument  is  the  sole  responsibility  of  the  pilot  in 
command  (PIC)  of  the  aircraft.  This  person  must  be  proficient  and  carry 
a valid  and  relevant 

pilot’s  license.  This  person  has  to  make  themselves 

familiar  with  the  operation  of  this  instrument  and  the  effect  of  any 
possible  failure  or  malfunction.  Under  no  circumstances  does  the 
manufacturer condone usage of this instrument for IFR flights. 

This  manual  defines  the  scope  of  maintenance  measures  the  user  is 
authorised to conduct  on their own. Any  repairs or  modifications outside 
this scope conducted by the user or contracted to a third party, as well as 
using non-original parts and subassemblies voids the warranty, relieves the 
supplier  from  any  liability,  making  the  instrument  lose  the  status  of  the 
product  of  Auto  &  Aero  Technologies  Sp.  z  o.o.  with  all  the  resulting 
consequences. 

 

2.  Handling in transport and storage 

1.

 

The  EEM  AM4  monitor  is  bubble-wrapped  to  protect  it  against 
vibration  and  other  physical  damage,  and  packed  in  a  cardboard 
box together with the warranty card.  

2.

 

The display must be stored and transported assuring that:  

Summary of Contents for EEM AM4 01 AR02




















Reviews: