background image

2

Important Safety Information

READ AND FOLLOW ALL INSTRUCTIONS

•  Read this manual completely before attempting installation and/or operation.
•  Install in accordance with the installation instructions.
•  Connect to a grounded, grounding type receptacle only.
•  Follow all applicable electrical codes.
•  To avoid electric shock, be sure to turn power OFF and disconnect from power source 

before any service work is performed. Failure to do so could result in serious injury or 
death. A licensed electrician should make all electrical connections. Replace damaged 
electrical cables immediately.

•  Install the ozone generator at least five feet from water using nonmetallic plumbing. 
•  Install check valves to prevent water from contacting the electrical equipment. 
•  The electrical supply for this product must include a suitably rated switch or circuit 

breaker to open all ungrounded supply conductors.

•  Ambient temperature around the equipment should be between 40 and 100 degrees 

Fahrenheit (4.5 to 38 degrees Celsius). If the equipment is installed in an environment 
with temperatures over 100 degrees Fahrenheit, additional air cooling must be provided. 
Installation without additional air cooling in an environment where temperatures exceed 
100 degrees Fahrenheit for any continuous 24-hour period will void the warranty. 

•  For your safety, do not store or use gasoline, chemicals or other flammable liquids or 

vapors near this or any other appliance. 

•  A spontaneous and violent ignition may occur if oil, grease or greasy substances come in 

contact with oxygen under pressure. These substances must be kept away from oxygen 
regulators, cylinder valves tubing and connections, and all other oxygen equipment. 

WARNING 

– Short term inhalation of high concentrations of ozone and long-term 

inhalation of low concentrations of ozone can cause serious harmful physiological effects. 

PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

 

In Accordance With California Regulations -- This Ozone Generator is Solely for Industrial 

use and Must Be Installed by a Professional. Potential Health Hazard: Emits Ozone.

Summary of Contents for SP Series




























Reviews: