A.R.I. D-070-P Installation Operation & Maintenance Download Page 20

20

 

IOM D-070-P

 

 

 

 

 

7. A.R.I. LIMITED WARRANTY 

 

 

A.R.I. Standard International Warranty 
 

A.R.I.  manufactured  products  are  guaranteed  to  be  free  from  defect  in  material  and/or 
workmanship  and  to  perform  as  advertised  when  properly  installed,  used  and  maintained  in 
accordance with current instructions, written or verbal. 
Should any item prove defective within the time period set forth for that item(s), but in any case 
not  later  than  within  12  (Twelve)  months  of  that  product  having  left  A.R.I.

s  premises,  and 

subject  to  receipt  by  A.R.I.  or  its authorized  representative,  of  written notice  thereof  from  the 
purchaser within 30 days of discovery of such defect or failure - A.R.I. will repair or replace or 
refund the purchase price, at its sole discretion, any items proven defective in workmanship or 
material. 
 
A.R.I. will not be responsible, nor does this warranty extend to any consequential or incidental 
damages or expenses of any kind or nature regardless of the nature thereof, including without 
limitation,  injury  to  persons  or  property,  loss  of  use  of  the  products,  loss  of  goodwill,  loss  of 
profits or any other contingent liabilities of any kind or character alleged to be the cause of loss 
or damage to the purchaser. 
 
This warranty does not  cover damage or failure caused by misuse,  abuse or negligence,  nor 
shall it apply to products upon which repairs or alterations have been made by other than an 
authorized A.R.I. representative. 
This  warranty  does  not  extend  to  components,  parts  or  raw  materials  used  by  A.R.I.  but 
manufactured  by  others,  which  shall  be  only  to  extent  warranted  by  the  manufacturer

warranty. 
 
THERE  ARE  NO  WARRANTIES,  EXPRESSED  OR  IMPLIED,  EXCEPT  THIS  WARRANTY 
WHICH  IS  GIVEN  IN  LIEU  OF  ANY  OTHER  WARRANTIES,  EXPRESSED  OR  IMPLIED, 
INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. 
 
 
Guy Sagie 
Chief Executive Officer

 

 

 

 

 

 

 

 

 
 

Summary of Contents for D-070-P





















Reviews: