background image

30              

 

 

 

Instruction manual TWI 35-130 G/TWI 45-190 G

3.10.3  Connect the mains voltage

The device is delivered without power cable and main switch.

 Remark

 

In order to supply voltage to the device, connect the device to the mains 

voltage using a permanent electrical connection. Place a double pole main 
switch with a contact opening of min. 3 mm between this permanent connection 
and the device. The power cable shall have a core of min. 3 x 1.0 mm².

 Warning

 

Keep the device electrically isolated until you are ready to start it up.

1. 

Connect phase (L), zero (Z) and earth  (

)  of the power cable to the    

 connector 

(C).

2. 

Mount the power cable into the strain relief (D).

3. 

Connect the power cable to the main switch.

4. 

Remount the cover plate.

3.10.4  Isolating transformer

An isolating transformer is used when a ‘

fl

 oating zero’ is present. Consult the 

mounting instructions delivered with the isolating transformer (contact the 
supplier for the correct isolating transformer). 

 Remark

 

Fill the device before starting up the device and/or checking the CO

2

-value 

(5 “Fill”)

.

 Caution

 

Checking the CO

2

-value is obligatory when starting up the device for the 

fi

 rst time.

 Remark

 

You obviously need a CO

2

-gauge for checking the CO

2

-value.

3

3.11 Check 

and 

 adjust 

the 

 CO

2

-value

Installation

Summary of Contents for TWI 35-130































































Reviews: