A.O. Smith LILY, User Manual

Page: 16 / 56

ENG 14
• Open the tap water inlet valve and the water purifier inlet water ball
valve (See Diagram 13) and plug the unit in the power outlet. Close
the storage tank ball valve, then automatically start a 120 second
flushing process, water will start to drain through the discharge outlet.
• Wait for the water purifier to operate stably (for about 5-10 minutes).
Check each connection to make sure they are secure. Check to see if
there is any leakage from the membrane shell, filters, etc.
• Close the pure water osmosis faucet and storage tank ball valve. Wait
approximately 30 seconds. Check to see whether or not the water
purifier waste water and high pressure pump have stopped working.
• Open the osmosis faucet. Check to see if the water is flowing through
the faucet. If not, check to see whether the tap water pressure is too low
or whether or not the high pressure switch can be reset automatically.
• Wait until the machine is operating properly, then close the inlet water
ball valve. After a short period of time, check to see if the machine stops
working, if it does not stop working, check to see whether or not
the low-pressure switch can be reset.
• Perform a second check to make sure everything is ok. Now your water
purifier is ready for use.
• Installation of UV Lamp:
First be sure that the water inlet and electricity connections are cut off from
the unit. Open the front cover, remove the UV lamp protector, and take
out the UV lamp and 2 pin cables from package, put one end 2 pins of UV
lamp into the hole end of cable connector, then put another end 2 pins of
UV lamp and 2 pins plug of cable together into the 4 holes end connector
and tight. Then install the cables and UV lamp into the stain steel tube
assembly, and make sure the 4 holes connector also inside, then cover the
end with cap and fix the cover (See Diagram 11).
• RO Unit Placement:
Lily RO unit is not wall hung type, and need put on the ground or solid flat
surface directly. If choice to hung on the wall, need to purchase additional
expand bolts and screws for fixation.
• Installation of the Storage Tank:
Wrap 4-5 rounds thread seal tape on the tank nozzle, then fix the tank
valve into the tank nozzle, then cut out a suitable length 1/4” tube, put one
end of tube on the tank valve, and another end connected to the “Tank”
joint of the unit (See Diagram 12). After that, find a suitable place to locate
the tank in the cabinet.
Diagram 11
Diagram 12
Diagram 13
Adjustment Methods
Make sure that the water route connections are correct, proper power supply is used and water supply is suitable.
Then, follow these steps to adjust the purifier:
ENG 15
Adjustment Methods
Make sure that the water route connections are correct, proper power supply is used and water supply is suitable.
er ball
the storage tank ball valve, then automatically start a 120 second
Check each connection to make sure they are secure. Check to see if
Close the pure water faucet and storage tank ball valve. Wait
approximately 30 seconds. Check to see whether or not the water
hrough
the faucet. If not, check to see whether the tap water pressure is too low
or whether or not the high pressure switch can be reset automatically.
Wait until the machine is operating properly, then close the inlet water
ball valve. After a short period of time, check to see if the machine stops
working, if it does not stop working, check to see whether or not
the low-pressure switch can be reset.
Perform a second check to make sure everything is ok. Now your water
Diagram 13
In these “operation methods”, “operation” refers to the power
supply
being connected and/or the inlet water ball valve being open
The major components of this product are manufactured using plastic.
of the equipment in order to ensure safe operation.
The package of the reverse osmosis membrane contains a small amount
of protective solution in order to prevent microbiological contamination
of membrane components during storage and transportation. The post
t time
the water produced during this period is disposed of. Otherwise,
the taste of the pure water may be unusual.
water.
be a little high. After operating for some time, the TDS value of the pure
water produced will gradually decrease until it is stable.
be opened and the pure water faucet needs to be turned on. When
you are not using water turn off the water faucet, the high pressure
switch will automatically cut off the water supply.
Operation Methods
so
3
3-Way Joint
Close
Open
ENG 14
7) UV lamp installation
Open the front cover, remove the UV lamp protector, and take out the UV lamp and 2 pin cables from package, put one end 2 pins of UV lamp into the hole
end of cable connector, then put another end 2 pins of UV lamp and 2 pins plug of cable together into the 4 holes end connector and tight. Then install the
cables and UV lamp into the stain steel tube assembly, and make sure the 4 holes connector also inside, then cover the end with cap and fix the cover.
8) Drinking machine fixation
The drinking machine is not wall hung type, and need put on the ground or solid flat surface directly. If choice to hung on the wall, need to purchase
additional expand bolts and screws for fixation.
9) Storage tank installation
Wrap 4-5 rounds thread seal tape on the tank nozzle, then fix the tank valve into the tank nozzle, then cut
out a suitable length 1/4” tube, put one end of tube on the tank valve, and another end connected to the
“Tank” joint of the unit (see diagram 12). After that, find a suitable place to locate the tank in the cabinet.
Protector
2 Pins Cable
Stain Steel
Tube Assembly
UV Lamp
4 Holes Connector Cap
Tank Valve
Nozzle
1/4”
Tube
Diagram 11
Diagram 12
Tank
Base