manualshive.com logo in svg

A-Link WL54AP, User Manual

Share
Download
A-Link WL54AP User Manual Download Page 40

 

40

milliseconds after the port trigger action during which incoming requests will be accepted. 

 

5. Choose Enable or Disable from the drop-down list for Session Chaining. This parameter 

specifies whether or not dynamic sessions can be chained, allowing multi-level session 

triggering. 

 

6. If you chose Enable in Step 5, you may now choose Enable or Disable for Chaining on UDP. 

If you chose Disable in Step 5, skip to Step 7. 

 

7. Choose Enable or Disable from the drop-down list for Address Replacement. This 

parameter specifies whether or not binary address replacement should be performed. 

 

8. If you chose Enable in Step 7, you may now choose the Address Translation Type (TCP or 

UDP). If you chose Disable in Step 7, skip to Step 9. 

 

9. Choose Enable or Disable from the drop-down list for Multi Hosts. Enabling this parameter 

allows a new session to be initiated from/to different remote hosts. 

 

10. Click Apply to put your changes in effect, or click Cancel to undo your changes. 

 

To delete a special application: 

1. Enter 0 - 0 for Trigger Port Range. 

2. Click Apply

. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for WL54AP














































Reviews:

No comments

Brands by name

Popular brands

Load more brands