manualshive.com logo in svg

A-Link WL54AP, User Manual

Share
Download
A-Link WL54AP User Manual Download Page 39

 

39

․

Special Apps 

Use the Special Applications screen to allow certain ports to communicate with computers 

outside your network. This feature may be necessary for multi-session applications like online 

gaming and video conferencing. The Special Apps screen is shown in the figure below. 

 

 

To configure Special Apps using the Popular Applications feature: 

1. Select the application you wish to enable from the Popular Applications drop-down list

:  

 

2. Choose a specific line in the table by selecting its number from the ID drop-down list. 

3. Click Copy to. The configuration settings for the selected application will appear in the table. 

4. Click Apply to put your changes in effect, or click Cancel to undo your changes. 

 

Manual Configuration 

Although you can manually configure special applications, only expert users should do so. We 

recommend that you always use the Popular Applications feature unless you know exactly 

which settings to choose. 

 

To manually configure Special Apps: 

1. Choose a line item to configure.   

 

2. Select the communication Protocol used by the application from the drop-down list (TCP, 

UDP, or Both). 

 

3. Specify a Trigger Port Range. This parameter identifies the range of ports that, when used 

for outgoing traffic, will trigger the gateway to accept certain incoming requests. 

 

4. Type a Maximum Activity Interval. This parameter specifies the maximum number of 

Summary of Contents for WL54AP














































Reviews:

No comments

Brands by name

Popular brands

Load more brands